Farm King Model 1050 Скачать руководство пользователя страница 165

Страница: 165 / 174

163

Specifications - 10" Backsaver Auger

HARDWARE TORQUE VALUES (CONT’D)

Imperial Chart

NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified in

this manual for a specific application. Torque values listed are for general use only.

Use the following charts to determine the correct torque when checking, adjusting or replacing hardware.

Torque values are listed in newton-meters (inch* or foot pounds) for normal assembly applications.

Nominal

Size

SAE Grade 5

SAE Grade 8

LOCK NUTS

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Unplated

Plated

Silver

Plated

W / ZnCr

Gold

Grade

W / Gr. 5

Bolt

Grade

W / Gr. 8

Bolt

1/4

6.2 (55*)

8.1 (72*)

9.7 (86*)

12.6

(112*)

13.6

(121*)

17.7

(157*)

6.9 (61*)

9.8 (86*)

5/16

13 (115*) 17 (149*) 20 (178*) 26 (229*) 28 (250*) 37 (324*) 14 (125*) 20 (176*)

3/8

23 (17)

30 (22)

35 (26)

46 (34)

50 (37)

65 (48)

26 (19)

35 (26)

7/16

37 (27)

47 (35)

57 (42)

73 (54)

80 (59)

104 (77)

41 (30)

57 (42)

1/2

57 (42)

73 (54)

87 (64)

113 (83)

123 (91)

159 (117)

61 (45)

88 (64)

9/16

81 (60)

104 (77)

125 (92)

163 (120) 176 (130) 229 (169)

88 (65)

125 (92)

5/8

112 (83)

145 (107) 174 (128) 224 (165) 244 (180) 316 (233)

122 (90)

172 (127)

3/4

198 (146) 256 (189) 306 (226) 397 (293) 432 (319) 560 (413) 217 (160) 306 (226)

7/8

193 (142) 248 (183) 495 (365) 641 (473) 698 (515) 904 (667) 350 (258) 494 (364)

289 (213) 373 (275) 742 (547) 960 (708) 1048 (773)

1356

(1000)

523 (386) 739 (545)

NOTE: Torque values shown with * are inch pounds.

Identification of Hex Cap Screws and Carriage Bolts

Identification of Hex Nuts and Lock Nuts

SAE GRADE

2 BOLTS

SAE GRADE

5 BOLTS

SAE GRADE

8 BOLTS

SAE GRADE

2 NUTS

SAE GRADE

2 NUTS

SAE GRADE

2 NUTS

Grade A - No Notches

Grade B - One Circumferential Notch

Grade C - One Circumferential Notches

Grade A - No Mark

Grade B - Letter B

Grade C - Letter C

Grade A - No Marks

Grade B - Three Marks

Grade C - Six Marks

(Marks not always located at corners)

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды