Farm King BW200 Скачать руководство пользователя страница 46

Страница: 46 / 82

Maintenance - 200 Bale Wrapper

STORAGE AND RETURN TO SERVICE

Storage

Sometimes it may be necessary to store the
equipment for an extended period of time. Below
is a list of items to perform before storage.

Thoroughly clean the equipment.

Inspect the hitch and all welds on the equipment
for wear and damage. Check for loose hardware,
missing guards, or damaged parts.

Check for damaged or missing safety signs
(decals). Replace if necessary.

Replace worn or damaged parts. Touch up all paint
nicks and scratches to prevent rusting.

Place the equipment in a dry protected shelter.

NOTE: If a dry protected shelter is not available,

cover with a waterproof tarp and tie down
securely.

Place the equipment flat on the ground. Place
planks under support stand if required.

Return To Service

After the equipment has been in storage, it is
necessary to follow a list of items to return the
equipment to service.

Be sure all shields and guards are in place.

Connect to a tractor and operate equipment, verify
all functions operate correctly.

IMPORTANT

DO NOT permit children to play on or around the
stored machine.

SAFETY SIGN (DECAL) INSTALLATION

Remove all portions of the damaged safety sign
(decal).

Thoroughly clean the area with cleaning product.

Removing all adhesive residue.

Allow the area to dry completely before installing
the new safety sign (decal).

Position the safety sign (decal) in the correct
location.

Remove a small portion of the backing paper on
the safety sign (decal).

Press on the safety sign (decal) where the backing
paper has been removed.

Slowly remove the remaining backing paper,
pressing on the safety sign (decal) as the backing
paper is removed.

Using the backing paper, pressing firmly, move
the backing paper over the entire safety sign
(decal) area.

NOTE: Small air pockets can be pierced with a pin

and smoothed out using the piece of the
backing paper.

IMPORTANT

When replacing safety signs (decals), the
temperature must be above 10° C (50° F).

Содержание BW200



















































































Результаты поиска

Содержание BW200

Отзывы:

Бренды по названию

Популярные бренды

Farm King BW200, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание BW200

Отзывы:

Бренды по названию

Популярные бренды