manualshive.com logo in svg

Farm King BW200, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Farm King BW200 Скачать руководство пользователя страница 43

Maintenance - 200 Bale Wrapper

41

TROUBLESHOOTING

WARNING

Instructions are necessary before operating or servicing equipment. Read and understand the Operator 
And Parts Manual and safety signs (decals) on equipment. Follow warnings and instructions in the 
manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, 
repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

NOTE: If a problem is encountered that is difficult to solve, even after having read through this 

troubleshooting section, please call your local Farm King dealer. Before you call, please have this 
Operator And Parts Manual and the serial number of your machine at hand.

PROBLEM

CAUSE

CORRECTION

Wrapping machine hydraulic 
actuators work slowly or do 
not work at all.

Not enough oil in the tractor 
hydraulic system.

 
Pressure in the tractor hydraulic 
system too low.

 
Wrong diameter setting of the 
external diameter lever.

Damaged actuator.

Check the oil level in the 
tractor. Top up oil.

 
Check the tractor hydraulic 
system pressure.

 
Turn on the pump drive.

 
Replace the actuator

The wrapping machine works 
too slowly.

Not enough oil in the tractor 
hydraulic system.

Check the oil level in the 
tractor. Top up oil.

Oil leaks from the control unit.

Worn seal rings.

Replace    the    seal    rings    
on    the hydraulic control unit.

Too wide or too narrow 
overlapping of film edges 
during wrapping.

Improper installation of the 
chain wheel.

Replace with a proper chain 
wheel.

The cut film is not held in the 
cutter unit.

The  rubber  clamp  holding  
the  cut  film  is  not adjusted 
properly.

Adjust the film pressure 
element.

Problems with bale unloading.

Rotary table lock does not 
operate.

Lock the table..

Содержание BW200



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды