Farm King 2400 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 112

Farm King 2400 Скачать руководство пользователя страница 43

Operation - Round Bale Carrier 2400

43

Loading Procedure

Move to the operator’s position, start the engine and
release the parking brake. (See “Entering The Operator’s
Position” on page 37.)

Move the tractor and bale carrier straight forward up to 5
mph (8 km/h), center the first bale in the bale forks.

Empty / Full Indicator

Figure 35

Indicator Down

- Available deck space for additional

bales or all bales have been removed (unloaded) from
deck.

Indicator Up

- When the bale carrier reaches its

capacity, bales will contact and move the rear indicator
backward, pulling the cable raising the front indicator
plate (upright) indicates not to load any more bales.

Before operating the equipment:

•

Clear the work area of all bystanders, especially
small children.

•

Clear the work area of all obstacles.

•

Keep shields and all guards in place.

•

Keep away from moving parts.

To avoid unbalanced loads, only push front bales
back one bale length to prepare for the next bale.

When loading bales, maintain a minimum of 2 ft. (61
cm) between rear bales and rear of carrier deck.
Rear bales must not extend beyond the carrier deck.

B-10056

CARRIER DECK EMPTY

CARRIER DECK FULL

At the end of the unloading process, front indicator
comes down (after pushing off the last bales)
warning the operator to release pusher back button,
then move forward, lower beam and bring the
pusher home (fully forward).

«
...
41
42
43
44
45
...
»

Содержание 2400

















































































































Отзывы:

Нет отзывов