manualshive.com logo in svg

Farm King 13114, Руководство оператора и каталог запасных частей, Страница: 16 / 268

Поделиться
Скачать
Farm King 13114 Скачать руководство пользователя страница 16

Safety - 13" Backsaver Auger

16

SAFETY INSTRUCTIONS (CONT’D)
Machine Requirements And Capabilities

•

Fasten seat belt securely. If equipped with a

foldable Roll-Over Protective Structure (ROPS),

only fasten seat belt when ROPS is up and locked.

DO NOT wear seat belt if ROPS is down.

•

Machine’s three-point hitch must be equipped with
sway bars or chains

.

•

Stop the machine and engage the parking brake.

Install blocks in front of and behind the rear tires of

the machine. Install blocks underneath and support

the equipment securely before working under

raised equipment.

•

Keep bystanders clear of moving parts and the

work area. Keep children away.

•

Use increased caution on slopes and near banks

and ditches to prevent overturn.

•

Make certain that the Slow Moving Vehicle (SMV)

emblem is installed so that it is visible and legible.

When transporting the equipment, use the flashing

warning lights (if equipped) and follow all local

regulations. 

•

Operate this equipment with a machine equipped

with an approved Roll-Over Protective Structure

(ROPS). Always wear seat belt when the ROPS is

up. Serious injury or death could result from falling

off the machine.

•

Before leaving the operator’s position:

1. Always park on a flat level surface.

2. Place all controls in neutral.

3. Engage the parking brake.

4. Stop engine.

5. Wait for all moving parts to stop.

•

Carry passengers only in designated seating areas.

Never allow riders on the machine or equipment.

Falling off can result in serious injury or death.

•

Start the equipment only when properly seated in

the operator’s seat. Starting a machine in gear can

result in serious injury or death.

•

Operate the machine and equipment from the
operator's position only.

•

The parking brake must be engaged before leaving

the operator’s seat. Rollaway can occur because

the transmission may not prevent machine

movement.

Содержание 13114













































































































































































































































































Отзывы:

Нет отзывов