Farm King 13114 Скачать руководство пользователя страница 13

Страница: 13 / 268

Safety - 13" Backsaver Auger

SAFETY INSTRUCTIONS

Safe Operation Is The Operator’s Responsibility

Safe Operation Needs A Qualified Operator

For an operator to be qualified, he or she must not use

drugs or alcoholic drinks which impair alertness or

coordination while working. An operator who is taking

prescription drugs must get medical advice to

determine if he or she can safely operate a machine

and the equipment.

A Qualified Operator Must Do The Following:
Understand the Written Instructions, Rules and

Regulations

•

The written instructions from Farm King include

the Warranty Registration, Dealer Inspection

Report, Operator and Parts Manual and machine

signs (decals).

•

Check the rules and regulations at your location.

The rules may include an employer’s work safety

requirements. Regulations may apply to local

driving requirements or use of a Slow Moving

Vehicle (SMV) emblem. Regulations may identify a

hazard such as a utility line.

Have Training with Actual Operation

•

Operator training must consist of a demonstration

and verbal instruction. This training is given by the

machine owner prior to operation.

•

The new operator must start in an area without

bystanders and use all the controls until he or she

can operate the machine safely under all conditions

of the work area. Always fasten seat belt before

operating.

Know the Work Conditions

•

Clear working area of all bystanders, especially

small children and all obstacles that might be

hooked or snagged, causing injury or damage.

•

Know the location of any overhead or underground

power lines. Call local utilities and have all

underground power lines marked prior to operation.

•

Wear tight fitting clothing. Always wear safety

glasses when doing maintenance or service.

This symbol with a warning statement means:

“Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

Safety Alert Symbol

The signal word CAUTION on the machine and in the

manuals indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury. It may also be used to alert against

unsafe practices.

The signal word DANGER on the machine and in the

manuals indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

The signal word WARNING on the machine and in the

manuals indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

This notice identifies procedures which must be

followed to avoid damage to the machine.

Operators must have instructions before operating

the machine. Untrained operators can cause injury or

death.

Содержание 13114













































































































































































































































































Результаты поиска

Содержание 13114

Отзывы:

Farm King 13114, Руководство оператора и каталог запасных частей, Страница: 13 / 268

Результаты поиска

Содержание 13114

Отзывы: