Farm King 13114 Скачать руководство пользователя страница 123

Страница: 123 / 268

Operation - 13" Backsaver Auger

123

Figure 278

Turn the handle (Item 1)

[Figure 278]

clockwise to

raise the hitch or counterclockwise to lower the hitch.
Lower or raise the Backsaver Auger hitch until aligned

with the tractor’s drawbar.
Move to the operator’s seat, start the engine and

release the parking brake.
Move the tractor backwards, aligning the drawbar

hitch pin hole with the Backsaver Auger hitch pin

hole(s).

Stop the tractor and leave operator’s position.

NOTE: Always use a hitch pin of adequate size and

strength and a retaining pin with a locking

device.

Figure 279

Install the hitch pin (Item 1)

[Figure 279]

and retaining

pin to securely fasten the Backsaver Auger hitch to

the tractor drawbar.
Attach the safety chain (Item 2)

[Figure 279]

around

the drawbar.

Connecting The PTO Driveline

NOTE: Clean and grease tractor’s PTO shaft and PTO

driveline coupling each time driveline is

connected.

Stop the engine and leave the operator’s position.

(See “Leaving The Operator’s Position” on page 122.)

Remove the PTO driveline from the storage position (if

applicable).

B-0728

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

connecting and disconnecting equipment.

B-0530

AVOID INJURY OR DEATH

Warnings on the machine and in the manuals are for

your safety. Failure to obey warnings can cause

serious injury or death.

Improper hitch installation can cause PTO driveline

damage.

•

Do not modify the hitch or use an unapproved

hitch.

•

Make sure the PTO driveline is of adequate length

and that u-joints are in the correct phase.

Содержание 13114













































































































































































































































































Результаты поиска

Содержание 13114

Отзывы:

Farm King 13114, Руководство оператора и каталог запасных частей, Страница: 123 / 268

Результаты поиска

Содержание 13114

Отзывы: