manualshive.com logo in svg

Farm King 13114, Руководство оператора и каталог запасных частей, Страница: 122 / 268

Поделиться
Скачать
Farm King 13114 Скачать руководство пользователя страница 122

Operation - 13" Backsaver Auger

122

Entering And Leaving The Operator’s Position

Entering The Operator’s Position

Move to the operator’s position, start the engine and

release the parking brake.

Leaving The Operator’s Position

Park the tractor / equipment on a flat level surface.
Place all controls in neutral, engage the park brake,

stop the engine and wait for all moving parts to stop.

Leave the operator’s position.

INITIAL SET-UP

Connecting The Backsaver Auger To The Tractor

Always inspect the tractor’s drawbar and Backsaver

Auger hitch before connecting. See the tractor’s

owner’s manual.
Verify that the tractor’s drawbar is adjusted correctly

for use with the Backsaver Auger. (See “Drawbar

Adjustment” on page 121.)
Enter the operator’s position. (See “Entering The

Operator’s Position” on page 122.)
Move the tractor into position in front of the

Backsaver Auger.

Move the tractor backwards, aligning the drawbar

with the Backsaver Auger hitch.

NOTE: The jack may need to be lowered or raised for

proper alignment of the drawbar and hitch.

If the Backsaver Auger hitch needs to be adjusted,

stop the tractor when drawbar is just in front of the

Backsaver Auger hitch.
Leave the operator’s position. (See “Leaving The

Operator’s Position” on page 122.)

Follow the instructions in your tractor’s operation

manual for the correct procedure.

AVOID INJURY OR DEATH

Before you leave the operator’s position:

•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

AVOID INJURY OR DEATH

Before moving the tractor, look in all directions and

make sure no bystanders, especially small children

are in the work area. Do not allow anyone between

the tractor and the equipment when backing up to

the equipment for connecting.

Содержание 13114













































































































































































































































































Отзывы:

Нет отзывов