FANOX SIA-B Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

FANOX SIA-B Скачать руководство пользователя страница 7

www.fanox.com

Installation_Guide_SIAB000B0010AA_Rev. 03 7 / 32



Warning

HAZARD OF EXPLOSION

•

Do not recharge the battery.

•

Do not short circuit the battery.

•

Do not crush the battery.

•

Do not disassemble the battery.

•

Do not heat the battery above 100ºC (212ºF)

•

Do not throw the battery into fire or water.

Failure to follow these instructions can result in death, severe injury, or equipment damage.

1.5. Relay rear part

Consider the wiring of the switchgear and connect relay properly:

A1

Phase A current input for measurement and self-power

C1

Trip

A2

Phase A current output for measurement and self-power

C2

Trip output

–

A3

Phase B current input for measurement and self-power

C3-C4

External trip

A4

Phase B current output for measurement and self-power

C5

Auxiliary power

A5

Phase C current input for measurement and self-power

C6

Auxiliary power supply -

A6

Phase C current output for measurement and self-power

╧

Earthing screw

1.6. Connection diagram

1.6.1. Connection diagram. Three phase diagram, neutral internally calculated

«
...
5
6
7
8
9
...
»

Содержание SIA-B

































Отзывы:

Нет отзывов