FANOX SIA-B Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

FANOX SIA-B Скачать руководство пользователя страница 15

www.fanox.com

Installation_Guide_SIAB000B0010AA_Rev. 03 15 / 32

7. FLOWCHART

7.1. Test menu

From the main menu, press the keys “◄”, “▼”, and “►” in sequence and then press and hold
the  "OK"  key  until  the  "Test  menu"  appears  on  the  display.  The  test  menu  is  accessed  by
pressing the "OK" key  again, and the “▲” and “▼” keys can be used to navigate through the
different  menu  items.  Each  item  can  be  activated  or  deactivated  by  pressing  "OK"  on  it  (if  the
item  is  deactivated,  it  is  activated  by  pressing  OK;  if  the  item  is  activated,  it  is  deactivated  by
pressing “OK”). Press the “C” key to exit the test menu.

Once “Led 1” appears, pressing “OK” the led is activated and pressing “OK” again, it is
deactivated.

To go through all options, press “▼”. To activate and deactivate the options follow the same
steps as in case of Led 1.

7.2. Direct Access

Version

The equipment versions menu can be accessed from the standby mode screen by holding “▲”
key.

Press the

“C” key to return to the standby mode screen.

«
...
13
14
15
16
17
...
»

Содержание SIA-B

































Отзывы:

Нет отзывов