manualshive.com logo in svg

Fanotec MECHA C2, Руководство пользователя

Поделиться
Скачать
Fanotec MECHA C2 Скачать руководство пользователя страница 119

119

MECHA C2 User’s Guide

v.02.5

© 2021 FANOTEC

C2 – C1 Differences and

Similarities

●

C2 can be connected to two rotators, so it can control two rotators

simultaneously.

○

C1 can control only one rotator at a time.

For dual axis applications, you need either one C2 controller and two

rotators or two C1 controllers and two rotators.

●

The C2 controller connects to the rotators with its built-in cable.

○

The C1 controller connects wirelessly to another C1, thus two C1 can

be assembled in DAC and control two axes.

●

The C2’s battery is external and you can quickly replace it when needed.

○

C1 has a built-in battery which lasts for one day after a full charge and

can be charged from a power bank or outlet adapter even while it is

in use.

Both systems allow MECHA to operate non-stop.

●

C2 has a 0.96 inch OLED display on which various data are

shown, including presets for shooting panoramas, code names,

warnings.

Codes

are special, predefined numerical combinations that you can use

to get information from MECHA or to ask MECHA to perform various

operations.

○

C1 has no display, but it has five LEDs with a similar function.

●

C2 has nine buttons, C1 has six.

○

-

The minus button of C2 is the equivalent of the

1

button of C1.

It comes pre-programmed with 4 shots around. It can also be used to

enter the number 1, or long press it to execute the

favorite code 1

.

Other special functions: adjusting values in preset editing mode,

deleting presets created in C2's menu.

Содержание MECHA C2



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды