fann 100072577 Скачать руководство пользователя страница 48

Страница: 48 / 73

Cement Curing Autoclave User Manual

100072577

Revision H

5.7

Pressurize the chamber

5.7.1

Connect the pressure source to the manual valve.

5.7.2

Open the manual valve at least one (1) and not more than two (2)

full turns.

5.7.3

Operate the pressure source to increase the pressure inside the

curing chamber to the desired initial value as required for the test. See
API RP 10B.

5.7.4

Close the manual valve to retain the chamber pressure.

5.7.5

If desired, the pressure source may be disconnected.

Figure 5-21

Set initial chamber pressure

5.8

Running a test

5.8.1

Adjust the set point of the temperature controller to the desired

maximum temperature. See API RP 10B for settings.

5.8.2

Program Temperature Control for a Test

5.8.2.1

From the home display, press until you reach

’ProG

LiSt’

. Press.

5.8.2.2

Use the arrow keys to select the number of the program to

be changed. Press.

5.8.2.3

For each program setting, use

to change the

displayed value. After releasing the button, the display will blink to show the
controller has accepted the new value.

Содержание 100072577










































































Результаты поиска

Содержание 100072577

Отзывы:

fann 100072577, Руководство пользователя, Страница: 48 / 73

Результаты поиска

Содержание 100072577

Отзывы: