background image

Important Safety Instructions

WARNING:

To avoid fire, shock and serious personal injury, follow these instructions.

1. Read  your  owner’s  manual  and  safety  information  before  installing  your  new  fan.  Review  the  accompanying  assembly

diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

power  from  being  switched  on  accidentally.  When  the  service  disconnecting  means  cannot  be  locked,  securely  fasten  a
warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling

fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To  avoid  possible  shock,  be  sure  electricity  is  turned  off  at  the  fuse  box  before  wiring,  and  do  not  operate  fan  without

blades.

2. All  wiring  and  installation  procedures  must  satisfy  National  Electrical  Codes  (ANSI/  NFPA  70-1999)  and  Local  Codes.  The

ceiling  fan  must  be  grounded  as  a  precaution  against  possible  electrical  shock.  Electrical  installation  should  be  made  or
approved by a licensed electrician.

3. The  fan  base  must  be  securely  mounted  and  capable  of  reliably  supporting  at  least 35 lbs.  (fan  and  accessories  not  to

exceed 35  lbs.  or 15.88  kgs.).  See  page  4  of  owner’s  manual  for  support  requirements.  Consult  a  qualified  electrician  if  in
doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow  the  recommended  instructions  for  the  proper  method  of  wiring  your  ceiling  fan.  If  you  do  not  have  adequate

electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

WARNING:

To  reduce  the  risk  of  fire  or  electric  shock,  this  fan  should  only  be  used  with  Fan  Speed  Control  Part  No.

UC7067RYL, manufactured by Rhine Electronic Co., Ltd.

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE, 

ISOLATING WALL CONTROL/SWITCH.

WARNING:

This  product  is  designed  to  use  only  those  parts  supplied  with  this  product  and/or  accessories  designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in
personal injury or property damage.

WARNING:

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

WARNING:

Mount to an outlet box marked acceptable for fan support.

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED  LIFETIME  MOTOR  WARRANTY  -  If  any  part  of  your  fan  motor  fails,  due  to  a  defect  in  materials  or  workmanship

during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective
fan  is  returned  to  our  national  service  center.  Proof  of  purchase  is  required.  Customer  shall  be  responsible  for  all  costs
incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due

to  defects  in  materials  or  workmanship,  labor  to  repair  the  motor  will  be  provided  free  of  charge  at  our  national  service
center.  Purchaser  will  be  responsible  for  labor  charges  after  this  one-year  period.  Customer  shall  be  responsible  for  all
costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

3. If  any  other  part  of  your  fan  fails  at  any  time  within  one  year  after  original  purchase,  due  to  a  defect  in  materials  or

workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our
national service center.

4. Because  of  varying  climate  conditions,  this  warranty  does  not  cover  changes  in  the  finish,  including  rusting,  pitting,

corroding, tarnishing, or peeling.

5. This  warranty  is  void  and  does  not  apply  to  damage  from  improper  installation,  neglect,  accident,  misuse,  exposure  to

extremes of heat or humidity, or as a result of any modification to the original product.

6. All  costs  of  removal  and  reinstallation  of  the  fan  are  the  sole  responsibility  of  the  owner  of  the  fan  and  not  the  store  that

sold the fan or Fanimation.

7. Fanimation  reserves  the  right  to  modify  or  discontinue  any  product  at  any  time  and  may  substitute  any  part  under  this

warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must

accompany  authorized  returns  and  must  be  sent  freight  prepaid  to  Fanimation.  The  fan  to  be  returned  must  be  properly
packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It  is  understood  that  any  repair  or  replacement  is  the  exclusive  remedy  available  from  Fanimation.  There  is  no  other

expressed  or  implied  warranty.  Fanimation  hereby  disclaims  any  and  all  implied  warranties,  including,  but  not  limited  to
those  of  merchantability  and  fitness  for  a  particular  purpose  to  the  extent  permitted  by  law.  Some  states  do  not  allow
limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out
of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you
special legal rights and you may also have other rights that vary from state to state.

10. A certain amount of wobble is normal and should not be considered a problem or a defect.

Unpacking Instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .4
Electrical and Structural Requirements  . . . . . . . . . . . . . . . . . .4
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .5
How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .7
How to Wire Your Ceiling Fan  . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Install Your Canopy Housing  . . . . . . . . . . . . . . . . . . . .9
How to Install the Light Bulb  . . . . . . . . . . . . . . . . . . . . . . . . . . .9

How to Assembly the Blades & Light Kit . . . . . . . . . . . . . . . . 10 
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . 12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
How to Clean Your Ceiling Fan Blades  . . . . . . . . . . . . . . . . . .14

How to Replace Receiver  . . . . . . . . . . .  . . . . . . . . . . . . . . . . . .14

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Exploded-View Illustration  . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Table of Contents

Содержание The Sandella MAD3260





































Отзывы: