STEP 1
Fold the template on the line indicated.
Place on
HIGH EDGE
of door bevel.
Position centerline of the template on heightline
(suggested height is 38" (965 mm) from floor).
A.
Locate and mark center for 2
¹⁄₈
" (54 mm) hole.
B.
Locate and mark positions for notches.
Caution
: Notches must be horizontal.
C.
Locate and mark center for two (2)
⁵⁄₁₆
" (8 mm)
through-bolt holes.
D.
Locate and mark center for 1" (25 mm) latch bolt hole
in the door edge.
Note: If steel frames are used, the latch centerline must
be in line with the center of the strike preparation.
Hint: For retrofitting of existing 2
¹⁄₈
" (54mm) holes, fold template in half to locate position for the two (2)
⁵⁄₁₆
" (8mm) holes.
MARK THE DOOR
INSTALLATION INSTRUCTIONS FOR INSTALLING
T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1
³⁄₄
" (45 mm)
THICK DOORS. TO ADJUST LOCK FOR OTHER DOOR THICKNESS, SEE STEP 8, 9 & 10. SPACERS MUST BE
USED FOR DOORS THINNER THAN 1
³⁄₄
" (45mm) THICK. FOR FUNCTIONS T351, T381, T561 AND T571,
SEE STEPS 16 (STANDARD CYLINDER) OR 17 (IC CORE) FOR TIMING INSTRUCTIONS.
Set Screw
¹⁄₄
-20 x
¹⁄₄
"
Mounting Screws
#10-32 x 1"
Outer Trim Assembly
Interchangeable Core Cylinder
Inner Lever
Rose
Inner Trim Assembly
Flanged Nut
Inner Mounting Plate
*Spacer
Attaching Screws
#8 Combination
*Spacer
*Spacer required for all
doors less than 1
³⁄₄
" thick.
Latch Assembly
Chassis Assembly
Outer Trim Assembly
Standard Cylinder
LEFT HAND REVERSE SHOWN
INSIDE
OUTSIDE
LEFT H
AND
LEFT
HAND REVERSE
RIGHT
HAND
RIGHT
HAND REVERSE
DOOR HAND DETERMINED FROM OUTSIDE
OUTSIDE
INSIDE
High Edge Of Bevel Door
D) Mark Latch Hole
A) Mark 2
¹⁄₈
" Hole
C) Mark Thru-Bolt Holes
TEMPLA
TE FOR
INST
ALLING
T–SERIES LEVER
LOCKS
LATCH
MARK CENTER FOR
5/16"(8mm) HOLES
USING DRILL
FIXTURE
030736-000-50 IS
RECOMMENDED
TO
ENSURE PROPER
ALIGNMEN
T OF
THRU-BO
LT
HOLES.
2 3/4"(70mm) BACKSET
MARK CENTER FOR
2 1/8"(54mm) HOLE
IMPOR
TAN
T:
CHECK LOCK FOR PROPER
BACKSET
BEFORE DRILLING
5/32"(4mm)
5/32"(4mm)
x1/8"(3mm) DEEP
R
D )
m
m1
5("
2
2
1
/
4
R
D )
m
m7
5("
1
3
/
4
R
D )
m
m5
4("
T
NE
MT
S
UJ
DA
G
NI
RE
T
NE
C
R
O
O
D
FOLD HERE &
PLACE ON HIGH
EDGE OF DOOR
MARK CENTERLINE OF L
ATCH
FOR CORRECT
DOOR
THICKNESS.
DRIL
L 1"(25mm) DIA
HOLE.
E
G
DE
H
GI
H
1 3/4"
(45mm)
2"(51mm)
2 1/4"(57mm)
B) Mark Notches
03079400070
