SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check ap pli ance is safe when you have finished.
35
Servicing
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS. TURN OFF THE GAS SUPPLY
Check the appliance is gas sound after completion
of service. When checking for gas leaks do not use
washing up liquid - this can corrode. Use a product
specifi cally manufactured for leak detection.
Do not use re-conditioned or unauthorised gas
controls.
Disconnect from the electricity supply before
commencing servicing, particularly before removing
any of the following: - control panel, side panels,
hotplate tray or any electrical components or covers.
Before electrical re-connection, check that the
appliance is electrically safe.
Note - References to LH and RH oven apply as
viewed from the front.
1 To Remove the Control Panel
Disconnect the appliance from the electricity supply.
Remove the pan supports and control knobs.
Remove the 3 screws at the rear of the top edge of
the control panel.
Open the oven doors and remove the 2 fi xing
screws, one at each end, underneath the control
panel. Lift the control panel, pull forward and
disconnect the wiring from the rear.
Replace in reverse order.
A Control panel top fi xing screws
B Hotplate front fi xing screws
C Hotplate back fi xing screws
2 To Remove the Hotplate top
Disconnect the appliance from the electricity supply.
Pull cooker forward to gain access.
Remove the control panel see 1. Remove the
hotplate burner caps and tops. If there are screws
holding the hotplate burners to the hotplate, remove
them (not the spark electrode fi xing screws).
Remove the 2 hexagon headed rear hotplate fi xing
screws and the 3 front hotplate fi xing screws. Lift
the hotplate clear of the appliance. Replace in
reverse order.
3 To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
Remove the control panel – see 1. Remove the
retaining screw on the upper front edge and the two
fi xings on the rear or the side panel. Undo the lower
retaining screw situated below the edge at the panel
front corner. Remove the panel by pulling it away
from the unit.
4 To Remove an Oven Neon
Remove the control panel – see 1. Hold the lens in
position at front of the panel and from the rear pull
the body of the neon out of the front lens. Hold
the front lens in position and from the rear of the
control panel fi t the new light to the lens. Replace
parts in reverse order. Ensure the replacement neon
functions correctly.
5 To Remove the Clock
Remove the control panel - see 1.
Pull off the timer control button(s). Remove the
timer/mounting bracket assembly from the facia
by removing the fi xing screws. Remove the timer
from its mounting bracket by depressing the plastic
lugs on the timer case, at the same time pulling the
unit forward. Reassemble in reverse order. When
replacing leads refer to the wiring diagram. Check
operation of timer.
6 To Remove a Thermostat
Disconnect the appliance from the electricity supply.
Remove the hotplate – see 2. Open the appropriate
oven door and remove the oven shelves.
RH oven
Remove the two fi xings that secure the thermostat
phial cover. Unclip the thermostat phial from the
clips in the oven back panel.
LH oven
Remove the two screws holding the thermostat
phial to the oven fan cover at the rear of the oven.
Pull the unit forward to access the rear of the cooker.
Remove the both cover boxes by removing the
fi xing screws and lifting clear. Feed the thermostat
capillary clear of the oven. Disconnect the wires
from the thermostat and undo the two fi xings that
secure the control to the mounting plate. Fit the
replacement and re-assemble in reverse order.
Ensure that the phial is clipped to the oven rear,
positioned centrally between the clips. Check that
the thermostat functions correctly.