Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 58

Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 49

NC-200 PB - Installation Manual - Page: 49

4.

OPERATION WITH THE RS-232-C SERIAL LINE

4.1.

SAVING AND RESTORING DATA

With this NC, it is possible to save data into a PC or peripheral device and later
restore it by using the RS-232-C serial communications line.
This data is sent out in the following format:
Baudrate as set by PAR90, 8 data bits, 1 stop bit and no parity.
To access this mode:

- Press

F

- Select the "

Com

" option (communications) of the LCD display by means of

the

and press

.

- Select: <

Send

> and press

to send the data out to a PC or peripheral

device or select <

Receive

> and press

to receive data from a PC or

peripheral device.

- Select the type of data to transmit

Param

eters,

Progr

am,

Mat

erials by means

of the

keys and press

.

4.2

PARAMETER TRANSMITTING FORMAT

The format of the transmitted parameters are:

For value parameters:

P?? 123.123

For binary parameters:

P?? 10101010

For option parameters:

P?? 0

For axis parameters:

P?? X 123.123 Y 123.123

The number of decimals depends on the selected resolution.

«
...
47
48
49
50
51
...
»

Содержание NC-200 PB - V0111



























































Отзывы:

Нет отзывов