manualshive.com logo in svg

Fagor NC-200 PB - V0111, Руководство по установке, Страница: 40 / 58

Поделиться
Скачать
Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 40

Page: 40 - Installation Manual - NC-200 PB

PAR21

Indicates the active level of the first 8 inputs.
By default, they are set to "1" meaning that they are activated with 24V.

Digit

Pin

8

33

BCD 2

7

14

BCD

6

32

Retract X axis / Feed in forced mode.

5

13

Go to next block

4

31

Y axis negative travel limit

3

12

X axis negative travel limit

2

30

Y axis positive travel limit

1

11

X axis positive travel limit

PAR22

Indicates the active level of the next 7 inputs.

By default, they are set to "1" meaning that they are activated with 24V.

Digit

Pin

8

Not being used at this time. It must be set to "0".

7

23

Emergency

6

8

"Return" foot switch.

5

36

External key 3 (A). EXECUTION mode selector

4

35

External key 2 (A). "BEND" foot switch.

3

16

External key 1 (A). EXECUTION mode selector

2

34

Disable the "Y" axis (Teach-in)

1

15

Hands-on palm switches / pressure level.

PAR23

Indicates the active level of the first 8 outputs.
By default, they are set to "1" meaning that when activated, they
provide 24V.

Digit

Pin

8

10

"H" output

7

27

Manual mode active

6

26

"Y" axis moving direction

5

7

"X" axis moving direction

4

25

"Y" axis fast movement

3

6

"X" axis fast movement

2

24

"Y" axis enable

1

5

"X" axis enable

PAR24

Indicates the active level of the next 3 outputs.
By default, they are set to "1".

Digit

Pin

8-4

Not being used at this time. They must be set to "0".

3

29

Axes in position (A). RAM down.

2

9

Buzzer. RAPID approach (B)

1

28

Retract RAM.

Содержание NC-200 PB - V0111



























































Отзывы:

Нет отзывов