manualshive.com logo in svg

Fagor NC-200 PB - V0111, Руководство по установке, Страница: 37 / 58

Поделиться
Скачать
Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 37

 NC-200 PB  -  Installation Manual - Page: 37

PAR03

External multiplying factor (EX E type) when using linear encoders
with distance-coded reference marks and TTL feedback signals.
Independent for each axis.

Options: 1, 5, 10, 20, 25, 50.

Factory setting: 1

These values are selected by pressing 

For example:

For 

standard Fagor linear encoders

 with squarewave signals (without

"

O

" or "

P

") e.g.: MX, CT, CX, etc. it must be set to "

1

".

For 

Fagor linear encoders with squarewave signals and distance-

coded reference marks 

(models with "

O

"),  eg.: MOX, COX, etc.

it must be set to "

5

".

For 

Fagor linear encoders with squarewave signals and distance-

coded reference marks 

(models with "

O

") and 0.5µm resolution,

eg.: MOY, COY, etc. it must be set to "

10

".

PAR05

Resolution (PAR01) correction factor.

It may be used for adapting any resolution, even fractional, when
the encoder is affected by a mechanical gear reduction.

PAR08

Feedback alarm enable. On if = 1 and Off if = 0.

Digit

3

Detects the feedback alarm provided by the encoder through pins
7 and 8.

Fagor models DO NOT provide this signal.

   rest

Not being used at this time. They must be set to "0".

Содержание NC-200 PB - V0111



























































Отзывы:

Нет отзывов