manualshive.com logo in svg

Fagor NC-200 PB - V0111, Руководство по установке, Страница: 27 / 58

Поделиться
Скачать
Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 27

 NC-200 PB  -  Installation Manual - Page: 27

2.4.2 Y AXIS REFERENCE (HOME) SEARCH. MODELS A AND A1

a- If the machine has travel limit switches, the home search procedure is the

same as the one described for the X axis; but it is only enabled if I13 = 1,
ram at top dead position.

b- If the machine does NOT have travel limit switches (which is very common

on down stroke models), set PAR14 bit 1 = 1 to indicate that the reference
position is floating.

The homing sequence is as follows:

·

In MANUAL mode, move the Y axis in the  Y+ direction to make sure that
the backlash is properly compensated for.

If P17 = 1, the Y- movement will be affected by the unidirectional approach
and will return in the Y+ direction.

·

Press the "BEND" footswitch until the ram reaches its final position. Output
O27 is active ("A" model) to enable the footswitch.

·

Measure the distance between 

the support bases of the punch and die.

This distance will be the Y

ref

 to be preset.

·

Press 

 . The 

 led will turn on. Enter the password (719200).

This unit displays the real position and the axis remains on stand by.

·

Select the 

 axis, (by default, it suggests the PAR10 value) and preset the

reference value Y

ref

 and press 

 to assume it. It displays the coordinate

( Y = Y

ref

 - H

punch

 - H

die

) compensating the height of the tools that are active.

See section 2.4.5

Содержание NC-200 PB - V0111



























































Отзывы:

Нет отзывов