Fagor NC-200 PB - V0111 Скачать руководство пользователя страница 16

Страница: 16 / 58

Page: 16 - Installation Manual - NC-200 PB

PIN

FUNCTION

Models A1, B and C

36 16

1 - RUN 1

2 - RUN 2

3 - SET

4 - JOG

Model A
External key
simulation. PAR 31

Model A1, B and C
footswitch connection

Models A, A1

Next block

Models A, A1
Double function
F1 + F2

Model A, A1

Mode B, C

The change to SLOW is forced at a previous programmable position

DESCRIPTION

Not connected. if the machine does not have a pressure sensor.

Pressure sensor
section 2.3.4

FAST approach before the bend conditioned to the maneouver safety
that requires "busy hands".

Model B

A - Electrical signal from the pressure sensor

Allows duplicating any 3 keys that may be selected - PAR 31

35, 36,

F2 - Forced X axis feed at the beginning of the bending sequence if
PAR65.2 = 1

8, 35

They respond according to the logic defined with the "BCD" selector

Confirmation of RAM at top dead position. Make sure that I13=1 to
begin the home search (A, A1, B)

If PAR65.1=1, requires previous input at I32

A1 - Confirmation that the programmed maximum pressure has been
exceeded to begin the delay "D".

F1 - Retracts the backstop X if there 's a conflict when bending,
conditioned by the editing attribute B in the slow speed stage

The X backstop automatically retracts at the position:
Y = sheet thickness

Only F2

Disables the axes
Disables the outputs

11, 12,

30, 31

Limit switches.
Hardware

EXTERNAL
EMERGENCY

In MANUAL mode, they limit the movement in the corresponding
direction.

In EXECUTION mode, they abort the program.

In HOME SEARCH mode, they respond as home switches in the
positive direction

"BCD" selector

36, 16

Displays error 20

2, 3, 4 - Incremental feed with the pitch set by PAR 32

1 - Continuous feed

14, 33,

5-position BCD
selector in MANUAL
mode - PAR32

5 - Y axis disable in EDITOR / TEACH-IN mode. It only displays it. It
allows withdrawing the punch by external means in "C" mode.

Semiautomatic in EXECUTION mode

Содержание NC-200 PB - V0111



























































Результаты поиска

Содержание NC-200 PB - V0111

Отзывы:

Fagor NC-200 PB - V0111, Руководство по установке, Страница: 16 / 58

Результаты поиска

Содержание NC-200 PB - V0111

Отзывы: