Fagor CNC 8058elite T Скачать руководство пользователя страница 41

Страница: 41 / 90

Probing (·T· model).

CNCelite

8058 8060

8065

PRO

04. Prob

e mo

vement up to

the

grammed po

tion.

ꞏ41ꞏ

. 2106

2.3

G104. Probe movement up to the programmed position.

When programming function G104 together with G100 or G103, the CNC makes the selected
probing movement, updates the coordinates when it receives the probe signal, but keeps
moving the axes until they reach their programmed position.

Function G101 may be used to make the CNC assume the measuring error resulting from
a G104 movement,

Probing programming.

The G104 must be programmed together with a G100 or G103 probe movement; otherwise,
it will be ignored.

Programming format.

The programming format is: Optional parameters are indicated between angle brackets.

G100 G104 X..C <F>
G103 G104 X..C <F>

Properties of the function and Influence of the reset, turning the
CNC off and of the M30 function.

Function G104 is not modal; it only acts in the block where it is programmed.

X..C

Coordinates of the probing point.

Optional. Feedrate.

If not programmed, the CNC uses the active feedrate.

G100 G104 Z23.45
G103 G104 Z1 F20

Содержание CNC 8058elite T



























































































Результаты поиска

Содержание CNC 8058elite T

Отзывы:

Похожие инструкции для CNC 8058elite T

Бренды по названию

Популярные бренды

Fagor CNC 8058elite T, Руководство пользователя

Результаты поиска

Содержание CNC 8058elite T

Отзывы:

Похожие инструкции для CNC 8058elite T

Бренды по названию

Популярные бренды