FabiaTech FX5201 страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 65

background image

FabiaTech Corporation

Default setting: Enable

¾

First /Second /Third/Boot Other Device/ Boot Device

This field specifies which device the system looks first upon power on.

Available options: LS120, Hard Disk, ZIP100, USB-ZIP, USB-CDROM, USB-HDD, LAN and

Disable

Default setting: Hard Disk, CDROM, LAN

¾

Boot Up Numlock status

This field is used to activate the Num Lock function upon system boot. If the setting
is on, after a boot, the Num Lock light is lit, and user can use the number key.

Available options: On, Off

Default setting: On

¾

Gate A20 Option

This item is chosen as <Normal>, the A20 signal is controlled by keyboard controller

or chipset hardware. The selection is “Fast” Port 92 or a chipset specific method
controls means the A20 signal

Available options: Normal, Fast

Default setting: Normal

¾

Typematic rate Setting

This function specifies the keystroke repeat rate when a key is pressed and held
down.

Available options: Disable, Enable

Default setting: Disable

Typematic Rate (Chars/Sec)

Typematic Rate sets the rate at which characters on the screen repeat when a key

is pressed and held down.

Available options: 6, 8, 10, 12, 15, 20, 24, or 30 characters per second

Default setting: 6

24

«
...
28
29
30
31
32
...
»

Содержание FX5201


































































Отзывы:

Нет отзывов

Похожие инструкции для FX5201

Бренд: IBM Страницы: 198

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 46

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 72

Бренд: Gateway Страницы: 72

Бренд: Radio Shack Страницы: 52

Desktop 5130DQ-IL

Бренд: Supermicro Страницы: 107

Бренд: Majestic Страницы: 24

TORO WORKSTATION JBTORO15WS

Бренд: J.Burrows Страницы: 8

Бренд: UMAX Technologies Страницы: 40

Presario 3500 Series

Бренд: Compaq Страницы: 68

FlowControl FC-S01

Бренд: Go!Paint Страницы: 20

Бренд: Ruijie Networks Страницы: 30

Бренд: GE Страницы: 112

Centricity RA600

Бренд: GE Страницы: 278

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды