ø12
0
ø150
100 100
ø 8
7
Z
X
48
20
650
105
105
200_05A
2
1
1
2
1
1
2
1
1
6"
round
6"
round
1/4"
3/4"
1 7/8"
3 15/16"
3 15/16"
INSTALL THE CANOPY
1.
Remove the unit from the carton and place on a
flat surface for assembly. Cover the surface to prevent
accidental damage. Remove all parts including the mounting
hardware before discarding the carton. DO NOT REMOVE
THE PROTECTIVE PLASTIC UNTIL INSTALLATION IS
COMPLETE.
2.
For ducted installations, attach the duct adaptor to the
rear of the blower
(FIGURE 6A)
. For ductless installations,
attach the vent grate to the top of the blower
(FIGURE 6B)
.
The cover over the vent opening must be removed before
installing the vent grate. The cover should be installed in the
rear vent opening.
PREPARE THE WALL
1.
Disconnect and move freestanding range from cabinet
opening to provide easier access to upper cabinet and rear
wall. Put a thick, protective covering over cooktop, set-in
range or countertop to protect from damage or dirt.
2.
Determine and clearly mark with a pencil the center line
on the wall where the rangehood will be installed.
3.
The Axia attaches to the wall by two mounting screws (
1
in FIGURE 5)
and an upper mounting bracket
(2 in FIGURE
5)
. Since the entire weight of the canopy is supported by the
two screws, these must be installed into solid material like
solid wood, brick or concrete. If these screws are installed
into sheet rock, then anchoring devices must be used suitable
for the weight of the rangehood. The position of the screws
(1 in
FIGURE 5)
are shown below. The height of the canopy
over the cooking surface will determine the position of the
screws. Install the two screws into solid material. These
screws should be installed into the wall leaving about 1/4"
between the head of the screw and the wall.
FIGURE 5
6.
Determine the proper location for the Power Supply
Cable. Use a 1 1/4" Drill Bit to make this hole. Run the
Power Supply Cable. Once the rangehood is installed, use
caulking to seal around the hole. DO NOT turn on the power
until installation is complete.
FIGURE 7
4.
The length of the chimney
(Z in FIGURE 5)
is adjustable
and determines where the upper bracket is installed
(2 in
FIGURE 5)
. The bracket attaches to the wall by one screw
. This bracket mounts to the underside of the blower and
supports the weight of the blower. Since the entire weight of
the blower is supported by this bracket, it must be installed
into solid material like solid wood, brick or concrete. If this
bracket is installed into sheet rock, then anchoring devices
must be used suitable for the weight of the blower.
FIGURE 6B
Version 02/02 - Page 5
3.
Remove the grease filters from the unit and set aside.
The grease filters are removed by pressing the handle in front
of the filter as indicated in
FIGURE 7
. When replacing, make
sure that the filters are properly positioned with the handles
in front and visible.
FIGURE 6A
4.
Install the two mounting screws
(O in FIGURE 8)
into the
wall. Attach the support rod
(B in FIGURE 9)
to the canopy
using the two screws
(Kin FIGURE 9)
provided.
FIGURE 9
FIGURE 8
5.
Determine and make all necessary cuts in the wall for
the ductwork. Install the ductwork before the rangehood. For
ductless installations, the duct cutout is not necessary.
Attach the upper bracket
(S)
to the
wall using the screw
(V )
provided.
