FAAC DAAB EP104 Скачать руководство пользователя

Страница: 16 / 74

Instruction manual version 1 for software version 4.04

INSTRUCTION MANUAL FOR DAAB EP104 CONTROL BOARD

Configuring the EP104

This section provides general instructions on how to change settings in the EP104.

It is a good idea to discharge any static charge in your body by always touching an earthed connection before starting installation.

• General

All values are stored according to a list of channels (in the channel reference), with each channel corresponding to a particular

control parameter or value in the EP104.

The display can show a value up to four digits long, or a channel number with the prefix C, d, L, o, P or r, followed by three

digits.

The display can be used to show values as well as change settings – the value flashes while the setting is being changed.

If E appears followed by a number, this is an error message – see "Error messages". Note that the start-up values "EP-1" and

"EP-2" are not error messages. When the power is connected, EP-1 appears when the unit controls one motor, and EP-2 when

the unit controls two motors.

The <

┘

button switches between the value and the channel number, or in configuration mode, it saves the value.

The + button scrolls up the channel list in channel mode. In configuration mode, the button increases the value.

The - button scrolls down the channel list in channel mode. In configuration mode, the button reduces the value.

If no button is pressed in 90 seconds, the display switches to economy mode with reduced brightness. Press any button to

return to normal mode.

Display

Description

Cnnn

Channel number for the EP104

dnnn

Channel number for the vehicle

detector

Lnnn

Channel number for the limit switch

onnn

Channel number for the output card

Pnnn

Channel number for programmable

inputs

rnnn

Channel number for the wireless card

Ennn

Error message (not EP-1 and EP-2)

nnnn

Readout of value

nnnn (flashing)

Value being changed

Button

Description

Button to increase the channel or value

Button to decrease the channel or value

┘

Switch between channel number and

value

┘

Save/confirm the changed value
Switch between different channel

groups

• Readout of parameters in the EP104

Press the <

┘

button so the display shows the channel number – a letter followed by digits.

Press the button to quickly change between letters (channel groups).

Press the + or - button to step to the channel number you want.

Press the <

┘

to show the value on the display.

Press the <

┘

button again to exit and return to the channel number. Leave the unit in this mode – you cannot exit any further.

• Setting parameters in the EP104

Select the channel number according to the readout above.

Press the + button. The value starts flashing and is ready to be changed.

Press the + or - button to step to the value you want.

Press the <

┘

button to save the value.

Press the <

┘

button again to exit and return to the channel number. Leave the unit in this mode – you cannot exit any further.

• Locked settings

Settings may be locked by service personnel so they cannot be changed. Contact an authorised service engineer, who will have

the instructions needed to release the unit for configuration.

Содержание DAAB EP104











































































Результаты поиска

Содержание DAAB EP104

Отзывы:

Похожие инструкции для DAAB EP104

Бренды по названию

Популярные бренды

FAAC DAAB EP104, Инструкция по эксплуатации

Результаты поиска

Содержание DAAB EP104

Отзывы:

Похожие инструкции для DAAB EP104

Бренды по названию

Популярные бренды