FA goods FA-TB16XYPN Скачать руководство пользователя страница 1

 

 

DC I/O Conversion Module 

FA-TB16XYPN 

User's Manual 

 

Thank you for purchasing FA Goods product. 

Before using, please read this User’s Manual and the relevant manuals carefully to 

ensure correct use.

 

 

 

 SAFETY PRECAUTIONS 

 

(Always read these precautions prior to use.) 

 

Before using this product, please read this User’s Manual and the relevant manuals carefully and pay 
full attention to safety to handle the product correctly.   
The precautions presented in this manual are concerned with this product only. For programmable 
controller system safety precautions, refer to the User’s Manual of the programmable controller to be 
used. 
In this manual, the safety precautions are classified into two levels: "      WARNING" and   
"   CAUTION". 

 

 WARNING 

 

Indicates that incorrect handling may cause hazardous   
conditions, resulting in death or severe injury. 

 

 

 

 CAUTION 

 

Indicates that incorrect handling may cause hazardous   
conditions, resulting in minor or moderate injury or   
property damage. 

 

 

 

Under some circumstances, failure to observe the precautions given under "        CAUTION" may lead 
to serious consequences. 
Observe the precautions of both levels because they are important for personal and system safety. 

 

Содержание FA-TB16XYPN

















Отзывы: