F5 i2000 Series Скачать руководство пользователя страница 50

Страница: 50 / 62

Item

Single power supply

Dual power supply

Idle power draw (AC power)

110VAC input: 95W
220VAC input: 90W

110VAC input: 95W
220VAC input: 95W

Typical power draw (AC power; 50% load;
temp 25°C)

110VAC input: 130W
220VAC input: 125W

110VAC input: 130W
220VAC input: 130W

Typical power draw (DC power; 50% load;
temp 25°C)

48VDC input: 135W

48VDC input: 145W

Maximum power draw (AC power)

110VAC input: 165W
220VAC input: 160W

110VAC input: 160W
220VAC input: 160W

Maximum power draw (DC power)

48VDC input: 165W

48VDC input: 180W

Typical heat generated (AC power)

110VAC input: 445 BTU/
hour
220VAC input: 430 BTU/
hour

110VAC input: 445 BTU/
hour
220VAC input: 445 BTU/
hour

Typical heat generated (DC power)

48VDC input: 465 BTU/
hour

48VDC input: 495W

Maximum heat generated (AC power)

565 BTU/hour

550 BTU/hour

Maximum heat generated (DC power)

565 BTU/hour

615 BTU/hour

Important: Specifications are subject to change without notification.

Safety requirements

This equipment complies with these requirements of the Low Voltage Directive 2014/35/EU:

EC Type Examination Certificates: Master Contract 252302

CB Scheme

EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

IEC 60950-1:2005, A1:2009+A2:2013

CSA 60950-1-07, Including A1:2011+A2:2014

ANSI/UL 60950-1-2014

EMC requirements

USA--FCC Class A, Canada--Industry Canada Class A

This equipment complies with Part 15 of FCC Rules. Operation is subject to these two conditions:

This equipment may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired
operation.

European Union

This equipment complies with these requirements of the EMC Directive 2014/30/EU:

Platform Specifications

Содержание i2000 Series































































Результаты поиска

Содержание i2000 Series

Отзывы:

F5 i2000 Series, Руководство по платформе, Страница: 50 / 62

Результаты поиска

Содержание i2000 Series

Отзывы: