manualshive.com logo in svg

F5 i2000 Series, Руководство по платформе

Поделиться
Скачать
F5 i2000 Series Скачать руководство пользователя страница 45

Guidelines for DC-powered equipment

A DC-powered installation must meet these requirements:

• Use a 15 amp external branch circuit protection device to install the unit.
• For permanently connected equipment, incorporate a readily accessible disconnect in the fixed wiring.
• Use only copper conductors.
• Cabling for the system must be grounded on both sides.
• Use one power feed for each individual power supply.

Caution: Install DC-powered equipment only in restricted access areas, such as dedicated equipment
rooms, equipment closets, or similar locations.

Avertissement : Installer le matérial alimenté par courant continu uniquement dans des zones à accès
reglementé, telles que des salles de matériel, des armoires de materiel ou tout emplacement similaire.

Platform airflow diagram

When you install the platform into a rack, it is important to understand the unit's airflow direction so that
you can ensure proper cooling.

The platform employs a negative pressure fan system, which draws cold air in from the front of the
chassis.

Platform Guide: i2000/i4000 Series

45

Содержание i2000 Series































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды