LED 450-EVS
GROW LIGHT SYSTEM
CONTENTS
1. EYE HORTILUX LED 450-EVS Ascend LED Grow Light System
™
2. Power cord
www.eyehortilux.com
EQS4631
OPTICAL RADIATION
Note that hazardous optical radiation may be emitted from this product.
Ensure the following precautions are taken:
NOTICE UV emitted from this product. Minimize exposure to eyes and skin.
Use appropriate shielding.
Visit eyehortilux.com for the latest installation instructions.
(Figure 1)
4’
4’
18”
Mounting Height:
18 inches from canopy
(Figure 2)
Hanging Tab
(Figure 3)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS BEFORE INSTALLATION.
•
WARNING - RISK OF SHOCK - DISCONNECT POWER BEFORE INSTALLING or SERVICING SYSTEM.
•
WARNING - Do not drape power cords over the system to avoid damage to cord.
•
WARNING - To prevent eye damage avoid looking directly at the LEDs.
•
CAUTION - RISK OF BURN: Driver box and LED boards may be hot. Do not touch system
when in operation or during cool-off period.
• The installation and use of the system is the responsibility of the end user. Incorrect use or
installation can lead to injury or death.
• Always adhere to the applicable electrical code, local rules and regulations when installing
or using the system.
• DO NOT open or disassemble the system, it contains no serviceable parts inside. Opening
the system and can cause electrical shock or electrocution.
• Use only with power cord supplied. DO NOT use the system when either its power cord or an
exposed wire is damaged. If cord of LED 450-EVS is damaged, it should be replaced with an
original EYE HORTILUX power cord.
• DO NOT modify cords. Modifications to the cords can lead to unwanted electromagnetic effects.
• Avoid coiled cords. Coiled cords may lead to electromagnetic interference.
• DO NOT use the system near flammable, explosive or reactive substances.
• Allow 30 minute cool down before handling the system.
• Make sure system is properly supported with supporting chains and/or hooks.
• DO NOT pull the cord to unplug the system, pull the plug only.
• DO NOT lift the system by any cords.
• DO NOT hang system by cord.
• DO NOT mount system directly touching any surface (maintain at least 3” from the
top of the system to mounting surface).
• DO NOT submerge system in water. System is designed to meet IP66. System is splash proof,
but not waterproof. In the event the system becomes submerged, first disengage the circuit
breaker, then unplug the system before removing it from water.
• DO NOT operate in ambient temperatures above 95°F/35°C. Note: Maintain the
temperature within the growing space below 86°F/30°C, otherwise ventilation/cooling
system may be required.
• It is possible to run multiple LED 450-EVS systems on one circuit. To determine the
maximum number of systems a circuit can run, consult a licensed electrician and review the
current and voltage specifications in this document. Ensure the total circuit load does not
exceed the circuit rating.
SYSTEM INSTALLATION INSTRUCTIONS
NOTE: Inspect system for defects prior to installation. If defects are noticed do
not install and contact the manufacturer immediately.
1. Remove LED 450-EVS from packaging.
2. Inspect for damage. If damage is noted, do not attempt to install
or operate.
3. This LED 450-EVS is intended to be hung using the attached four (4)
corner hanging tabs.
(Figure 1)
Use mounting hardware suitable for the
surface involved, attach chain. Hardware and chain are to be capable of
supporting 100 lbs.
4. Hang LED 450-EVS no closer than 18 inches above the plant canopy
for optimal growing.
(Figure 2)
Hanging height of less than 6 inches
is not recommended as plant growth and light uniformity will suffer.
(If hanging more than one system, ensure the edge-to-edge distance
between systems is greater than 4 inches. Optimal spacing is 8 inches.)
5. Plug female end of the input power cord into the system. To do so, turn
cord end to match internal key alignment of the socket. Push cord end
in firmly.
(Figure 3)
Note: repeated attachment could damage the cord.
6. Plug male end of the input power cord into the electrical outlet. If
using a hardwire cord, consult a qualified electrician for correct supply
termination. Use a suitably rated NEMA connector or hardwire (Black to
Line, White to Neutral, Green to Ground)
7. The LED 450-EVS is now ready for operation.
Thank you for purchasing the LED 450-EVS Ascend
LED Grow Light System
™
. This rugged system utilizes a
robust thermal and electrical design with an extended
spectrum. This premium growth spectrum includes
ultraviolet and far-red energy, promoting stronger plant
growth and heavier flowers.
