1
Product Category
XTP T HDMI and XTP R HDMI • Setup Guide
This guide provides instructions for an experienced installer to install and connect the Extron XTP T HDMI transmitter and XTP R HDMI receiver.
Transmitter Connections
Receiver Connections
a
DC power connector
b
HDMI input connector
c
HDMI Loop-thru connector
d
Analog audio input connector
e
RS-232/IR Over XTP
connector
f
XTP output connector
g
LAN connector
h
DC power connector
i
XTP input connector
j
LAN connector
k
RS-232/IR Over XTP connector
l
HDMI output connector
m
Analog audio output connector
n
S/PDIF audio output connector
o
Relay connectors
Installation
Step 1
—
Mounting
Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required.
Step 2
—
Connecting inputs
a.
Connect a digital video source to the female HDMI connector of the XTP T HDMI (see
b
above). It can accept HDMI, DVI (with an
appropriate adapter), or DisplayPort video signals.
NOTES:
•
Use an Extron LockIt
®
Locking Bracket to secure HDMI cables to the connectors.
•
Video input from a DisplayPort source must be a dual mode DisplayPort source.
b.
Connect a digital video display to the HDMI loop-thru connector on the transmitter to locally display the input source. Displays that are not
HDCP compliant display a green screen when HDCP encrypted content is sent to them (see
c
above).
c.
Connect balanced or unbalanced stereo audio to the
3.5 mm, 5-pole captive screw connector (see
d
above).
Step 3 — Connecting Throughput Devices
a.
Connect a twisted pair cable between the XTP connectors on
the transmitter and receiver (see
f
and
i
above).
ATTENTION:
Do not connect these connectors to a computer data or telecommunications
network.
The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Extron recommends using
the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce
transmission errors.
z
Use Extron XTP DTP 24 SF/UTP cable for the best performance. If not using XTP DTP 24
cable, at a minimum, Extron recommends 23 AWG, solid conductor, STP cable with a minimum
bandwidth of 400 MHz.
z
Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
z
Limit the use of more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are required, use
CAT 6 or 6a shielded couplers and punch down connectors.
NOTE:
When using CAT 5e or CAT 6 cable in bundles or conduits, consider the following:
•
Do not exceed 40% fill capacity in conduits.
•
Do not comb the cable for the first 20 m, where cables are straightened, aligned, and secured in tight bundles.
•
Loosely place cables and limit the use of tie wraps or hook and loop fasteners.
•
Separate twisted pair cables from AC power cables.
Signal LED
—
Lights on the transmitter when it is transmitting a video signal or a test pattern. Lights on the receiver when it receives an
active XTP input signal from the transmitter.
Link LED
—
Lights yellow when a valid link between an XTP input and output is established.
TIA/EIA T 568 B
Pin Wire Color
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A
T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Do not tin the wires!
Unbalanced Stereo Input
Balanced Stereo Input
Tip
Ring
Tip
Ring
Sleeves
Tip
Sleeve
Sleeve
Tip
LR
LR
POWER
12V
HDMI
1.0 A MAX
Rx G
Tx
RS-232
IR
Rx
Tx
−
+
−
+
L
R
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
SIG LINK
XTP OUT
INPUTS
OVER XTP
POWER
12V
1.0 A MAX
Rx
G
Tx
RS-232
IR
R
L
Rx
Tx
-
+
-
+
1
2
AUDIO
ON
AUDIO
RESET
OVER XTP
OUTPUTS
RELAYS
SIG LINK
XTP IN
LAN
HDMI
OFF
S/PDIF
XTP R HDMI Rear Panel
XTP T HDMI Rear Panel
g
a
b
k
m n
h
i j
f
d
c
o
e
l
