1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
USB HUB4 Series • Setup Guide
This guide provides basic instructions for setting up the Extron USB HUB4 Series AAP and MAAP.
HUB4 USB MAAP
HUB4 USB AAP
ACTIVITY
ACTIVITY
USB HUB4 MAAP
USB HUB4 AAP
ACTIVITY
ACTIVITY
Installation
Step 1 — (Optional) Install the wall box or mounting bracket
If using an electrical wall box or a mounting bracket, install it in the wall or furniture (see Mounting in the
USB HUB4 Series User
Guide
).
Step 2 — Mount the HUB4 onto a mounting frame
Attach the USB HUB4 AAP or USB HUB4 MAAP to an appropriate AAP or MAAP sized mounting frame, rack space frame, or
other Extron architectural product (see Mounting in the
USB HUB4 Series User Guide
).
Step 3 — Connect the USB HUB4 to the host computer
For ease of installation, connect the USB HUB4 to the host computer in either of the following ways:
•
Using the Type mini-B USB port:
Connect a Type A to Type mini-B cable (provided) to the
USB mini-B port on the USB HUB4 rear panel.
•
Using the green captive screw USB In port:
Remove the Type B or Type mini B terminator
from a Type A to B or Type A to mini-B USB cable and insert the cable wires into the 5-pole
USB In port as shown below and at right. This method may be necessary if space is limited.
(See Connecting to the captive screw USB port in the
USB HUB4 Series User Guide
.)
NOTE:
Choose one of these two methods to connect the HUB4 to the host computer.
Do not connect the host computer to both HUB4 ports at the same time.
Wire color
Port
Braided shield
V+ (+5 VDC)
Red
S (Shield)
White
D- (Data -)
Green
D+ (Data +)
Black
–
(Ground)
USB IN
R W G B
+V D- D+
S
IN
OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
-
-
-
Braided Shield / S
Red / +V
White / D-
Green / D+
Black /
USB Cable (6
'
)
To Host
Computer
USB Port
Type A
USB
Strip 1
"
to 2
"
from the outer jacket
of the USB cable to expose the wires.
USB HUB4 AAP
Captive
Screw
USB
Connector
Type mini B
USB Connector
Mounting
Frame
Rear
Step 4 — (Optional) Wire power connector
The USB HUB4 can be powered by the host computer. However, if the USB peripheral devices
connected to the USB HUB4 require more power than the USB HUB4 can provide, wire an
optional Extron PS 1215 1.5 A, 12 VDC power supply to the 12 VDC Power In ports 1 and 2 on the
rear panel, as shown at right.
ATTENTION:
•
For use only with UL Listed Extron products which accept Architectural Adapter Plates
(AAPs) or Mini Architectural Adapter Plates (MAAPs).
•
À utiliser uniquement avec les produits Extron certifiés UL qui acceptent des plaques
d’adaptation architecturale (AAP) ou des mini-plaques d’adaptation architecturale
(MAAP).
USB IN
R W G B
+V D- D+
S
IN
OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
-
-
-
SECTION A–A
Power Supply
Output cord
A
