4
68-2294-50 Rev. A
08 15
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
TLP Pro 1220TG and TLP Pro 1520TG • Setup Guide (Continued)
A
Power supply input
(see
figure 5
) — connect a 12 VDC, 3.0 A power supply (not provided) to this DC plug connector.
ATTENTION:
•
The touchpanels can use a 12 VDC desktop power supply and are also Power over Ethernet (PoE Plus IEEE
802.3at) compliant. Do not connect either power supply before reading the Attention in the Power section of the
TLP Pro 1220 Series and TLP Pro 1520 Series User Guide
.
•
Les écrans tactiles peuvent utiliser une source d’alimentation externe 12 Vcc, et sont également compatible avec
l’alimentation POE via Ethernet (PoE Plus IEEE 802.3at). Ne branchez pas de sources d’alimentation externes avant
d’avoir lu les mises en garde dans la section « Power Supply » du
TLP Pro 1220 Series and TLP Pro 1520 Series
User Guide
.
NOTE:
The TLP Pro 1220TG and TLP Pro 1520TG are shipped without a power supply. Either the 12 VDC, 3.0 A power
supply or the power injector must be purchased separately.
B
USB connectors
(see
figure 5
) — for peripheral controls.
C
Rear status light
(see
figure 5
) — an LED light bar that can be programmed to provide system feedback.
D
HDMI input
(see
figure 5
) — for alternative video input.
E
XTP/LAN/PoE input
(see
figure 5
) — is in the top of the recessed area.
XTP
input — Connect the touchpanel to the XTP source using a twisted pair cable,
terminated with an RJ‑45 connector.
LAN
input — Connect the touchpanel to the LAN using a twisted pair cable,
terminated with an RJ‑45 connector.
PoE
input — the connector can be used with a PoE plus power injector (not
provided). Connect the cables as shown in the figure to the right, which shows the
Extron PI 140 power injector (recommended by Extron).
An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.
F
Audio output
(see
figure 5
) — for use with headphones or assistive listening devices.
G
Menu button
(see
figure 5
) — activates the setup menu and calibration screen (see below).
H
Reset button
(see
figure 5
) — pressing the reset button allows the unit to be reset in any of three different modes. For full
information about the modes, see the
TLP Pro 1220 Series and TLP Pro 1520 Series User Guide
.
I
Reset LED
(see
figure 5
) — provides feedback about the reset status when the user presses the reset button.
J
VESA mounting holes (4)
(see
figure 5
) — for use with D‑type VESA mounting kits with the 100 x 100 mm mounting pattern.
K
Base attachment hinge
(2) (see
figure 5
) — each hinge secures the touchpanel to the base with two screws.
Reset Modes: a Brief Summary
The TLP Pro 1220TG and TLP Pro 1520TG offer the following reset modes:
•
Use factory firmware:
Press and hold the
Reset
button (
figure 5
,
H
) while applying power to the unit. Use this mode
to replace firmware in the event of firmware failure.
•
Reset All IP Settings:
Press and hold the
Reset
button for 6 seconds. After the Reset LED (
figure 5
,
I
) flashes
twice, release and momentarily press the
Reset
button. Use this mode to reset all network
settings without affecting user‑loaded files.
•
Reset to Factory Defaults:
Press and hold the
Reset
button for 9 seconds. After the Reset LED flashes three times,
release and momentarily press the
Reset
button. Use this mode to return the interface to
factory default settings.
Setup Menu
Press the menu button (
figure 5
,
G
) to open the setup menu. Select any
of the five available screens (
Status
,
Network
,
Display
,
Audio
,
Input
and
Advanced
) by pressing the appropriate button in the navigation bar at the
top of the screen (for more information, see the
TLP Pro 1220 Series and
TLP Pro 1520 Series User Guide
).
Figure 6 shows the setup menu for the TLP Pro 1220TG. The setup menu
for the TLP Pro 1520TG is identical.
Press the menu button for at least 3 seconds to open the calibration
screen. Follow the on‑screen instructions.
Figure 6.
Setup Menu: Status page for TLP Pro 1220TG
Info
Model:
TLP Pro 1220TG
Part Number: 60-1341-02
Firmware
Version:
1.02.0000.b003
PoE:
Active
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLI-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
1280x800
1280x800
5 Minutes
Audio
Master Volume:
Master Mute:
Off
100
Input
HDMI:
No Signal
Status
Display
Audio
Advanced
Exit
Network
Input
Advanced
Controller IP:
192.168.254.250
Project Size:
1/197 MB
Bootloader
Version:
1.03.0000
XTP:
1280x720
HDCP
100-240V~50/60 Hz
1.1A MAX
INPUT
OUTPUT
POWERED TLP
LAN
To Network or
XTP Device
To a TLP Pro
touchpanel
Extron PI 140
