1
Extron External Power Supply •
Installation Guide
About the Extron PS 910, PS 1210, PS 1508
Power Supplies
Model Overview
Model
Power Output
Termination
PS 910C
9 watts, 9 VDC, 1 A
Captive screw
PS 910P
9 watts, 9 VDC, 1 A
DC plug
PS 1210C
12 watts, 12 VDC, 1 A
Captive screw
PS 1210P
12 watts, 12 VDC, 1 A
DC plug
PS 1508C
12 watts, 15 VDC, 0.8 A
Captive screw
ZipClip
™
100
(101-002-01)
—
—
Cabling and Features
Features
1A MA
X
100-240V 50-60H
z
Power
LED
ZipClip
Mounting Slot
(front and rear)
AC
Power
Input
DC Power
Output
Notches for
Securing
Tie Wrap
Connector Pin Assignments
PS 910C, PS 1210C, PS 1508C
Alternative Wiring Option
PS 910P, PS 1210P
Sleeve (
-
)
Tip (
+
)
Power Supply
Output Cord
Power Supply
Output Cord
Captive Screw
Connector
Ridged
Smooth
Ridged
Smooth
N/C
Tie Wrap
Using the ZipClip 100
Attaching and Removing the Clip and Power Supply
To attach the power supply to the ZipClip 100 mounting clip:
1.
Insert the bottom of the power supply down into the clip,
starting with one end.
2.
Pivot the other end down and press until the clip snaps into place.
To remove the power supply from the ZipClip:
1.
Press the tab on the ZipClip.
2.
Pivot the power supply and lift it out
of the ZipClip.
b
a
2.
Fasten the power output cord to the ZipClip base.
a.
Insert tie wraps (“zip ties”) along the notches on the side of the
power supply and
through the tie wrap
anchor points on the
ZipClip, then around
the cord.
b.
Connect and pull the
tie wraps until they
are secure. Do not
over tighten.
Mounting
CAUTION:
These power supplies are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within
the vicinity of the Extron AV equipment in an ordinary location
with IEC 1010 pollution degree 2, and secured to an equipment rack
within a dedicated closet, podium, or desk.
The installation must be in accordance with the applicable provisions
of National Electrical Code ANSI/NFPA 70, article 75 and Canadian
Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to building or similar structure.
Rack Mounting
Mounting to a Rack Shelf
These power supplies are one eighth rack wide. Up to eight power supplies
can be mounted side by side directly onto a rack shelf.
1.
Align the threaded holes in the bottom of the power supply with the
holes in an Extron rack
shelf and fasten the
supply to the shelf
with two 4-40 x 3/16"
screws as shown
below.
2.
Bolt the rack shelf to the rack.
Mounting to Rack Rails Using a ZipClip
1.
Fasten the ZipClip 100
mounting clip to a
rack rail using
two rack
screws as
shown in the
diagram at
right.
2.
Insert the
power supply
into the ZipClip as
described previously
and press to snap it
into place.
Pole or Table Leg Mounting
1.
Wrap a tie wrap around
the projector mount pole or table
leg and the power supply at one of
the tie wrap notches, and fasten the
tie wrap together to secure the
power supply to the pole or table
leg.
2.
Repeat step 1 at the other tie wrap
notch.
Cable
Strain
Relief
Tie Wrap
a
b
(2) 4-40 x 3/16"
Screws
RSB 123
Rack Shelf
Side of Rack
ZipClip 100
Back of
Rack
Inside
Rack
Tie Wrap
to Pole
Important Safety Instructions
This symbol is intended to alert the user of impor-
tant operating and maintenance (servicing) instruc-
tions in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product enclosure that may present a risk of
electric shock. On the product, risk of shock may
be indicated by this symbol.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this device apparatus during lightning storms or when
unused for long periods of time.
WARNING:
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases shall be
placed on the apparatus.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as
when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING:
This apparatus is a Class I product. This product
must be connected to a MAINS socket outlet with a
protective earthing connection.
The mains plug is used as the disconnect device and shall remain
readily operable.
To prevent the risk of shock, do not attempt to service this
equipment yourself because opening or removing covers may
expose you to dangerous voltage or other hazards.
WARNING:
Power sources
• This equipment should be operated only from
the power source indicated on the product. This equipment
is intended to be used with a main power system with a
grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection
• To remove power from the equipment
safely, remove all power cords from the rear of the
equipment, or the desktop power module (if detachable), or
from the power source receptacle (wall plug).
See the next page for
furniture mounting instructions.
Using Tie Wraps for Cable Strain Relief
1.
Attach the power supply to the ZipClip mounting clip as described
previously.
