Extron electronics MultiMatrix SMX System Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

background image

20

SMX System MultiMatrix Switcher • SIS Programming Guide

Number of connections

An SMX can have up to 200 simultaneous TCP connections, including
all HTTP sockets and Telnet connections. When the limit is reached,
the SMX accepts no new connections until some have been closed. No
error message or indication is given that the limit has been reached.
To maximize performance unnecessary open sockets should be closed.

Verbose Mode

Telnet connections can be used to monitor changes that occur on
the SMX. The Telnet session must be in verbose mode 1 or 3. See the

Verbose Mode

commands on page 31.

Host-to-switcher Instructions

SIS commands consist of one or more characters per command
field and do not require any special characters to begin or end the
sequence. SMX responses to an SIS command ends with a carriage
return and a line feed, which signals the end of the character string
(a string is one or more characters).

]

= CR/LF (carriage return/line feed)

}

= Carriage return (no line feed)

•

= Space character

NOTES:

•

Commands can be entered back-to-back
in a string with no spaces. For example:

1*1&001*002*002&001*003*
003&001

•

The SMX supports 1-, 2-, and 3-digit numeric entries
(

1*1*1!, 01*02*02&, or 001*003*003%

).

Error Messages

E01

= Invalid input number

E24

= Privilege violation

E10

= Invalid command

E25

= Device no present (invalid plane/slot)

E11

= Invalid preset number

E26

= Maximum number of connections exceeded

E12

= Invalid output number

E27

= Invalid event number

E13

= Invalid parameter

E28

= Bad filename/file not found

E14

= Invalid for this

configuration

«
...
24
25
26
27
28
...
»

Содержание MultiMatrix SMX System

















































Отзывы:

Нет отзывов

Похожие инструкции для MultiMatrix SMX System

Бренд: Omega Engineering Страницы: 3

CT.TS005.003902

Бренд: Talkswitch Страницы: 309

Бренд: Bridgetek Страницы: 2

3CB9E7 - CoreBuilder 9000 Chassis Switch

Бренд: 3Com Страницы: 132

Бренд: Black Box Страницы: 3

Бренд: EtherWAN Страницы: 239

Бренд: Edimax Страницы: 8

ScatterBox POE308

Бренд: System Q Страницы: 2

Бренд: Lindy Страницы: 8

Бренд: AAVARA Страницы: 8

Бренд: Hama Страницы: 36

Бренд: Dwyer Instruments Страницы: 2

Бренд: ATEN Страницы: 30

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 4

NetVanta 1570-24-370W

Бренд: ADTRAN Страницы: 9

Бренд: Dell Страницы: 2

EMC PowerSwitch S5148F-ON

Бренд: Dell Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды