manualshive.com logo in svg

Extron electronics IP Link IPL EXP 200, Руководство пользователя, Страница: 26 / 52

Поделиться
Скачать
Extron electronics IP Link IPL EXP 200 Скачать руководство пользователя страница 26

IPL EXP I/O Series • Hardware Features and Installation

18

LAN/PoE and LAN/PoE+ (Ethernet) connectors and LEDs

To connect the EXP to an Ethernet network (for configuration and control of the EXP 
and the devices connected to it), plug a cable into one of these RJ-45 sockets and 
connect the other end of the cable to a power inserter, network switch, hub, router, or 
PC connected to a local network or the Internet. DHCP is off by default.

• 

The IPL EXP RIO8 requires a PoE+ connection through its LAN/PoE+ port see the 

power input requirement

 on page 14).

• 

All other IPL EXP  models accept power over Ethernet (PoE) and PoE+ through the 
LAN/PoE port

ATTENTION:

 

• 

Power over Ethernet (PoE) is intended for indoor use only. It is to be connected 
only to networks or circuits that are not routed to the outside plant or building.

• 

L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur 
uniquement. Elle doit être connectée seulement à des réseaux ou des circuits 
qui ne sont pas routés au réseau ou au bâtiment extérieur.

Network Port Addressing:

If you use static IP addresses, configure the settings and IP addresses via Toolbelt. See 
the help file for Global Configurator or Toolbelt for basic information on configuration. 
See the diagram on the next page and see the following table for default addresses.

Network Port Addressing

IP Address

Subnet Mask DNS Address

Static IP addresses

 (default, what the unit uses when DHCP is off)

192.168.254.250 255.255.255.0 127.0.0.1

DHCP on

 (alternative setting)

DHCP on (addresses are automatically assigned)

For details of communication protocols, ports, and services used, see the  

Pro Series Control Product Network Ports and Licenses Guide

 at 

www.extron.com

.

LED Indication:
Activity LED

 (connectors [all models] and front panel [rack mount models]) —  

This yellow LED blinks to indicate network activity.

Link LED

 (connectors [all models] and front panel [rack mount models]) —  

This green LED lights to indicate a good network connection.

100 LED

 (IPL EXP RIO8 front panel) — This green LED lights when the unit is 

connected to a 100 Mbps or faster network connection.

Passwords:

IMPORTANT NOTE:

   

The factory configured passwords for this device have been set to the device serial 
number. Passwords are case sensitive. Performing a Reset to Factory Defaults 
reset (see 

Resetting the Unit

 on page 29) sets the password to 

extron

.

Содержание IP Link IPL EXP 200





















































Отзывы:

Нет отзывов