Extron electronics IP Link IPL EXP 200 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

Extron electronics IP Link IPL EXP 200 Скачать руководство пользователя страница 25

IPL EXP I/O Series • Hardware Features and Installation

17

Bidirectional Control and Communication Connections and Features

3-pole COM ports, RS-232 only

All models except the IPL EXP RIO8 include COM ports, which can be used for serial
control of a display or other device and to receive status messages from the connected
devices. These ports can send commands from a driver file.

IPL EXP I/O Series serial protocol:

•

300 to 115200 baud (9600 baud = default)

•

8 (default) or 7 data bits

•

1 (default) or 2 stop bits

•

No parity (default), even parity, or odd parity

•

Flow control support (default = none),
software-only (XON, XOFF)

Use the following diagram as a wiring guide to cable
the EXP to other devices.

Tx Rx G

COM

Tx Rx G

1

2

Tx Rx G

COM 2

Tx Rx G

COM 1

NOTE:

If you use cable that has a drain wire, tie the drain wire to ground at both ends.

RS-232-

Controllable

Device

Transmit

Receive

Receive (Rx)

Transmit (Tx)

Ground

Rx

G

Tx

Strip wires
3/16" (5 mm) max.

3-pole COM

(RS-232)

Select protocol via software.

COM port default protocol:

• 9600 baud

• 8 data bits • 1 stop bit

• no parity

• no flow control

NOTE:

The 3-pole COM ports support

software flow control only.

Serial (COM) Ports

Rear Panels

Heat Shrink

To 3-pole
COM port

Heat Shrink

Over Shield Wires

or

Figure 7.

Wiring COM Ports for Serial Control

For bidirectional serial communication, the transmit, ground, and receive pins must be
wired at both the IPL EXP and the other device. Each projector or other device may require
different wiring. For details, see the manual for that equipment or read the Extron device
driver communication sheet, which is included with the drivers.

NOTE:

Maximum

distances between the EXP and the device being controlled are

generally up to 200 feet (61 m) but can vary based on factors such as cable gauge,
baud rates, environment, and output levels from the EXP and the device being
controlled.

3/16"

(5 mm)
Max.

7/8"

(22 mm)

Heat Shrink

on Outer

Jacket to

Inner

Conductor

Transition

Extron

STP 20-2P Cable

TIP:

STP 20-2P

cable, shown
at left, is
recommended
for these
connections.
For best
results,
insulate the
common or
drain wires
using heat
shrink.

«
...
23
24
25
26
27
...
»

Содержание IP Link IPL EXP 200





















































Отзывы:

Нет отзывов