Extron electronics FOXBOX HDMI, Руководство по установке, Страница: 1 / 4

1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
FOXBOX HDMI • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOXBOX HDMI fiber optic
extenders.
CLASS 1 LASER PRODUCT, see
FOXBOX HDMI
User Guide at
www.extron.com
CAUTION:
•
These units output continuous invisible light, which may be harmful to the eyes; use with caution. For additional safety, plug the
attached dust caps into the optical transceivers when the fiber optic cable is unplugged.
•
Ces produits émettent une lumière invisible continue, qui peut être dangereuse pour les yeux ; à utiliser avec précaution. Pour
une sécurité renforcée, associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble fibre
optique est débranché.
Installation
FOXBOX Tx HDMI Rear Panel
Front Panel
FOXBOX Rx HDMI Rear Panel
12V
1.0A MAX
POWER FOXBOX Tx HDMI
AUDIO INPUT
RS-232
OVER FIBER ALARM
Tx Rx 1 2
HDMI INPUT
LINK
OPTICAL
Rx Tx
LINK
FOXBOX Tx HDMI
AUDIO HDCP HDMI
CONFIG
HDMI LOOP THRU
EDID MINDER
50Hz
AUDIO
DIGITAL
ANALOG 60Hz
1 2
12V
1.0A MAX
POWER
LINK
OPTICAL
Rx Tx
LINK
HDMI AUDIO
HDMI
AUDIO
OUTPUTS
OFF
ON
REMOTE
RS-232
Tx Rx
RS-232
OVER FIBER ALARM
Tx Rx 1 2
L R
FOXBOX Rx HDMI
Step 1 — Mounting
Turn off or disconnect all equipment power
sources and mount the transmitter and
receiver as required.
Step 2 — Input and Output
Connections
a. Connect an HDMI video source to the
transmitter HDMI connector.
b. If desired, connect an HDMI video display to the transmitter HDMI Loop-Thru connector.
c.
Connect an HDMI video display to the receiver HDMI Output connector.
NOTE:
Use a LockIt™ Lacing Bracket to
securely fasten an HDMI cable to each device as follows
.
1. Plug the HDMI cable into the panel connection
3
3
1
2
4
5
2.
Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3.
Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION:
•
Do not overtighten the HDMI connector mounting screw. The shield it
fastens to is very thin and can easily be stripped.
•
Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage
auquel elle est attachée est très fin et peut facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5.
While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then
remove any excess length.
d.
Connect an audio input device to the transmitter Input Audio 3.5 mm mini jack.
e. Connect an audio device to the receiver Audio captive
screw connector. See the drawing at right.
ATTENTION:
•
For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.
• Pour l’audio asymétrique, connectez les manchons au contact au sol. NE PAS connecter les manchons aux
contacts négatifs (–).
Do not tin the wires!
Unbalanced Stereo Output Balanced Stereo Output
Tip
NO GROUND HERE
NO GROUND HERE
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves