Extron electronics FOX II T DP 4K, Руководство по установке

Страница: 1 / 4

1
IMP
ORT
ANT
:
Go to www
.extr
on.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
FOX II T/R DP 4K • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron FOX II T/R DP 4K Fiber Optic Extenders.
WARNING :
The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with
caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
CLASS 1 LASER PRODUCT , see the FOX II T/R DP 4K User Guide , at www.extron.com .
AVERTISSEMENT :
Le FOX II T/R DP 4K émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux
pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque
le câble fibre optique est débranché.
Produit laser de classe 1
, voir le FOX II T/R DP 4K User Guide sur www.extron.com (en anglais) .
Installation
FOX II DP 4K Transmitter Rear Panel
FOX II DP 4K Receiver Rear Panel
100-240V ~ -.-A MAX
50-60 Hz
DISPLAYPORT LOOP THRU
L R
RS-232
OPTICAL
Tx
RESET LINK LINK
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx Rx G
AUDIO
INPUTS AUDIO
RETURN OUT
REMOTE
OVER FIBER
FOX T DP 4K
100-240V ~ -.-A MAX
50-60 Hz
DISPLAYPORT
L R
RS-232
OPTICAL
Tx
RESET LINK LINK
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx Rx G
AUDIO
OUTPUTS AUDIO
RETURN IN
REMOTE
OVER FIBER
FOX R DP 4K
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the transmitter and receiver as required.
For mounting details and considerations, see the
FOX II T/R DP 4K User Guide at
www.extron.com
.
Step 2 — Input and Output Connections
a.
Connect a DisplayPort
DISPLAYPORT LOOP THRU
video source to the
transmitter DisplayPort input connector.
b.
If desired , connect a DisplayPort video display
to the transmitter Loop-Thru connector for a
local display.
c.
Connect a DisplayPort video display to the receiver DisplayPort output connector.
DISPLAYPORT
d.
Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector
L R
AUDIO
on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.
e.
Connect an audio output device to either or both the 3.5 mm mini jack or the Audio 5-pole captive screw connector
on the receiver. See the drawing below step 2g to make connections on the captive screw connector.
f.
For optional returned audio
, connect an audio output device to the Audio Return Out 5-pole captive screw
L R
AUDIO
RETURN OUT
L R
AUDIO
RETURN IN
connector on the transmitter. See the drawing below step 2g to make connections on the captive screw
connector.
g.
For optional returned audio , connect an audio input device to the Audio Return In 5-pole captive screw
connector on the receiver. See the drawing below to make connections on the captive screw connector.
ATTENTION:
• For unbalanced audio, connect the sleeves to the
ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
• Pour l’audio asymétrique, connectez les manchons au
contact au sol. Ne PAS connecter les manchons aux
contacts négatifs (–).
NOTE: For returned audio, above, and RS-232 and IR responses (from the receiver to the transmitter), on the next page , you
must install the receiver-Tx-to-transmitter-Rx cable in step 3b .
Unbalanced Stereo Output Balanced Stereo Output
Unbalanced Stereo Input Balanced Stereo Input
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Sleeves
Tip
Sleeve
Sleeve
Tip
LR