Extron electronics DXP 1616 HD 4K Скачать руководство пользователя страница 59

Страница: 59 / 116

DXP HD 4K Series • Operation

To perform a hardware reset of the switcher:

Use a stylus or small Philips screwdriver to press and

hold

the rear panel

Reset

button

until the front panel

Video

and

Audio

buttons blink twice (for a system reset) or three

times (for an absolute reset).

RESET

Release, then immediately
press and release again.

IP Settings

Reset

(Mode 4)

6 seconds

Absolute Reset

(Mode 5)

9 seconds

Reset LED blinks twice.

Reset LED blinks

three times.

Front panel I/O buttons or LEDs blink twice.

Front panel I/O buttons blink three times.

I / O

AUDIO

VIDEO

I/O

VIDEO

AUDIO

DXP 88 Series

DXP 1616 Series

I / O

AUDIO

VIDEO

I/O

VIDEO

AUDIO

DXP 88 Series

DXP 1616 Series

Press and hold
the

Reset

button.

Press and hold
the

Reset

button.

Figure 77.

Soft Resets (Modes 4 and 5)

Release the

Reset

button and then immediately press and release it again. Nothing

happens if the second momentary press does not occur within 1 second.

Selecting the Remote RS-232 Port Baud Rate

NOTES:

•

The serial port settings are protected when front panel lock mode 2 is selected. You
can view the settings in lock mode 2 but you cannot change them from the front
panel.

•

To enable changes to the baud rate settings, set the lock mode to

To view and configure the serial communications settings for the switcher from the front
panel:

Simultaneously press and

hold

all

Control buttons (

Enter

Preset

View

[DXP 168

and 1616 only] and

Esc

) until all of the Control buttons or their LEDs light, as well as

input buttons 1 and 2 (approximately 2 seconds).

Содержание DXP 1616 HD 4K





















































































































Результаты поиска

Содержание DXP 1616 HD 4K

Отзывы:

Extron electronics DXP 1616 HD 4K, Руководство пользователя, Страница: 59 / 116

Результаты поиска

Содержание DXP 1616 HD 4K

Отзывы: