manualshive.com logo in svg

Extron electronics DVS 605, Руководство пользователя, Страница: 18 / 133

Поделиться
Скачать
Extron electronics DVS 605 Скачать руководство пользователя страница 18

 

DVS 605 • Rear Panel Connections

10

I

 

Audio output (fixed)

 (audio models only)

 (see 

figure 1

 on page 7) — Connect 

audio output devices to this 5-pole, captive screw connector for line level, balanced or 
unbalanced, analog stereo.  
Wire the connectors as shown below.

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

No Ground Here

Tip

Sleeves

LR

LR

Do not tin the wires!

Figure 4. 

 Audio Output Connector Wiring

J

 

RCA audio output

 (S/PDIF, fixed, audio models only)

 — Plug in an S/PDIF audio 

output device into this female RCA connector. This connector outputs digital S/PDIF 
audio formats (2-channel LPCM, Dolby Digital, or DTS).

K

 

Audio output (variable)

 (audio models only) 

— Connect audio output devices to this 

5-pole, captive screw connector for line level, balanced or unbalanced, analog stereo. 
Wire the connectors as shown below.

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

No Ground Here

Tip

Sleeves

LR

LR

Do not tin the wires!

Figure 5. 

 Audio Output Connector Wiring

L

 

Reset button and LED

 

— Using an Extron Tweeker, pointed stylus, or ballpoint pen, 

press this recessed button for manual resets. The unit has three modes of reset (see 

Resetting the Unit

 on page 33 for additional information). The green LED blinks to 

show the reset mode indications and that power is on.

M

 

LAN connector

 

— Plug an RJ-45 jack into this socket to connect the unit to a 

computer network. Use a patch cable to connect to a switch, hub, or router.  
Wire the connector as shown below. 

 

12345678

RJ-45 Connector

Insert Twisted

Pair Wires

Pins:

Pin

1

2
3
4
5
6
7
8

Wire color

White-green

Green
White-orange
Blue
White-blue
Orange
White-brown
Brown

Wire color

T568A

T568B

White-orange

Orange
White-green
Blue
White-blue
Green
White-brown
Brown

Figure 6. 

 RJ-45 LAN Connector Wiring

LAN Activity LED

 

— A blinking yellow LED indicates LAN activity.

Link LED

 — The green LED lights to indicate a good LAN 

connection.

4 

5 

6 

LAN

Activity

Link

Содержание DVS 605






































































































































Отзывы:

Нет отзывов