DMP 64 Plus • SIS Configuration and Control
52
Command
ASCII command
(host to device)
Response
(device to host)
Additional description
Macro Commands
Run macro
E
R
X4*
MCRO
}
McroR
X4*
]
Kill macro
E
K
X4*
MCRO
}
McroK
X4*
]
Get macro status
E
S
X4*
MCRO
}
X4(
]
Set macro name
E
A
X4*
*
X5)
MCRO
}
McroA
X4*
*
X5)
]
Get macro name
E
A
X4*
MCRO
}
X5)
]
Set power-on macro
E
P
X4*
MCRO
}
McroP
X4*
]
Using
0
for
X4*
clears
power-on macro
assignment.
Get power-on macro
E
PMCRO
}
X4*
]
KEY:
X4*
= Macro number:
1
through
64
. Response will be padded with a leading
0
.
X4(
= Macro status:
0
= Macro idle,
1-32
= Macro step
X5)
= Macro name:
24 characters maximum (
A-Z
,
a-z
,
0-9
, and “
-
”)
Asynchronous Macro Commands
Macro started
McroSTARTED
X4*
]
Macro finished
McroFINISHED
X4*
]
Macro failed
McroFAILED
X4*
*
X4(
]
Macro killed
McroKILLED
X4*
*
X4(
]
KEY:
X4*
= Macro number:
1
through
64
. Response will be padded with a leading
0
.
X4(
= Macro status:
0
= Macro idle,
1-32
= Macro step
Dante Control and Configuration
The following commands configure the DMP 64 Plus to listen for and pass through SIS commands meant for Extron endpoints
controlled over Dante, such as AXI AT or NetPA Ultra AT devices.
NOTE:
The DMP must be set to Verbose mode 1/3 when using the Dante Control and Configuration commands.
Query available remote
devices
E
AEXPR
}
Verbose Mode 2/3
•
X*
]X*]
...
]]
ExprA
•
X*
]X*]
...
]]
Enable remote
connection for listening
E
C
X*
*
X2@
EXPR
}
Verbose Mode 2/3
X*
*
X2@]
ExprC
X*
*
X2@
]
All listening disabled
when DMP Dante module
rebooted
Read remote
connection listening
status
E
C
X*
EXPR
}
Verbose Mode 2/3
X2@
]
ExprC
X*
*
X2@
]
Query remote devices
being listened to
E
LEXPR
}
Verbose Mode 2/3
•
X*
]X*]
...
]]
ExprL
•
X*
]X*]
...
]]
Send command to
remote device
{dante@
X*
:
X5#
}
}
Verbose Mode 1/3
example command:
{dante@AXI-
RoomA:wg60000*-10AU
|
}
}
{dante@
X*
}
X5$
]
example response:
{dante@AXI-RoomA}DsG60000*-
10
]
KEY:
X*
= Dante device name:
Device names are not case sensitive.
X2@
= Extron remote connection mode:
0
= Macro idle
1
= Enabled
X5#
= SIS command:
SIS command to be sent to remote dante-controlled device.
X5$
= SIS command response:
Response from remote dante-controlled device, tagged by DMP.
Dante Control and Configuration
Query available remote devices
Enable remote connection for listening
Query remote devices being listened to