ExtremeSwitching 200 Series Скачать руководство пользователя страница 357 | Manualshive

Страница: 357 / 369

background image

EAP-TTLS (Tunneled Transport Layer Security) is an extension of EAP-TLS to provide certificate-based,
mutual authentication of the client and network through an encrypted tunnel, as well as to generate
dynamic, per-user, per-session WEP keys. Unlike EAP-TLS, EAP-TTLS requires only server-side
certificates.
(See also

PEAP (Protected Extensible Authentication Protocol)

.)

EAPS

Extreme Automatic Protection Switching is an Extreme Networks-proprietary version of the Ethernet
Automatic Protection Switching protocol that prevents looping Layer 2 of the network. This feature is
discussed in RFC 3619.

ECMP

Equal Cost Multi Paths is a routing algorithm that distributes network traffic across multiple high-
bandwidth

OSPF (Open Shortest Path First)

BGP (Border Gateway Protocol)

, IS-IS, and static routes to

increase performance. The Extreme Networks implementation supports multiple equal cost paths
between points and divides traffic evenly among the available paths.

EGP

Exterior Gateway Protocol is an Internet routing protocol for exchanging reachability information
between routers in different autonomous systems.

BGP (Border Gateway Protocol)

is a more recent

protocol that accomplishes this task.

ELRP

Extreme Loop Recovery Protocol is an Extreme Networks-proprietary protocol that allows you to detect
Layer 2 loops.

EMISTP

Extreme Multiple Instance Spanning Tree Protocol. This Extreme Networks-proprietary protocol uses a
unique encapsulation method for

STP (Spanning Tree Protocol)

messages that allows a physical port to

belong to multiple

STPD (Spanning Tree Domain)

EPS

Ethernet Protection Switching is defined in ITU/T G.8031.

ESRP

Extreme Standby Router Protocol is an Extreme Networks-proprietary protocol that provides redundant
Layer 2 and routing services to users.

ESS

Several

BSS (Basic Service Set)

s can be joined together to form one logical

WLAN (Wireless Local Area

segment, referred to as an extended service set (ESS). The

is used to identify the ESS.

FDB

The switch maintains a database of all MAC address received on all of its ports and uses this information
to decide whether a frame should be forwarded or filtered. Each forwarding database (FDB) entry
consists of the MAC address of the sending device, an identifier for the port on which the frame was
received, and an identifier for the

VLAN (Virtual LAN)

to which the device belongs. Frames destined for

devices that are not currently in the FDB are flooded to all members of the VLAN. For some types of
entries, you configure the time it takes for the specific entry to age out of the FDB.

Glossary

ExtremeSwitching 200 Series: Administration Guide

357

«
...
355
356
357
358
359
...
»

Содержание 200 Series


















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 200 Series

Бренд: CALIENT Страницы: 22

TNS5500D Series

Бренд: 3onedata Страницы: 5

IPS7112G-4GS-8GPOE

Бренд: 3onedata Страницы: 3

Бренд: Radial Engineering Страницы: 12

Бренд: JDS Uniphase Страницы: 37

Бренд: Lantronix Страницы: 2

Underwater Switch 24V DC/DMX/02

Бренд: Oase Страницы: 40

Бренд: CZHOON Страницы: 4

Бренд: CalDigit Страницы: 13

CN8000 KVM on the NET

Бренд: ATEN Страницы: 2

Бренд: Watt Stopper Страницы: 10

Бренд: Key Digital Страницы: 20

Бренд: Vega Страницы: 36

Бренд: IPGARD Страницы: 2

START-LINE AGC-3500

Бренд: Trust Страницы: 16

Бренд: ATEN Страницы: 4

Бренд: Edge-Core Страницы: 65

Бренд: Vagner Pool Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды