Extreme Networks Summit WMScanner Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 77

Summit WMScanner Users Guide

75

The

Configure Real-Time Measurement Run Information

dialog box appears.

The

Configure Real-Time Measurement Run Information

dialog box contains the following options for

tailoring measurement runs:

●

Description

-

All measurement data files are distinguished from one another by a unique

description that you provide in this edit box. The measurement description must consist of
alphanumeric characters. Extreme Networks recommends using this option to label the floor to
be measured and to document the person collecting the data.

●

Building Notes

- Provides a small scratch space to enter quick notes regarding the measurement

run before you begin.

●

Create ASCII Log File

- The collected measurement data is stored under the

Measured

directory of

the current project workspace. This file may be renamed as desired. It is recommended that the
file have the same name as the measurement run name you specify (this is the default,
automatically filled in when you change the description for the measurement run).

●

Receiver Height Above Floor

-

Specifies the vertical height (

Feet/Meters

) at which you will record

measurement data.

●

Marker Color

- This button allows you to set the color of markers you will be placing in the

drawing. The choice of marker color applies only during the measurement process, and may be
altered after the measurement run is complete.

●

Setup Instructions

- Select this button to display instructions for the measurement mode selected.

●

Select Measurement Mode

- Use this pull-down menu to the measure measurement mode:

«
...
75
76
77
78
79
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов