manualshive.com logo in svg

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 75 / 217

Поделиться
Скачать
Extreme Networks Summit WMScanner Скачать руководство пользователя страница 75

Summit WMScanner Users Guide

73

3

Measurement Surveys

Summit WMScanner 

eliminates the hassles involved in collecting data acquisition by implementing a 

point-and-click method of acquiring measurement data from your PC’s wireless LAN (WLAN) card. 
The following workflow diagram provides an overview of the primary measurement survey steps for 
recording measurements and visualizing the results. 

Summit WMScanner

 provides two site-specific means of recording measurement information:

●

RF Monitoring

 - Using a proprietary WLAN driver, Summit WMScanner

 

automatically collects data 

from all visible APs. For this process to function, the WLAN card must not be associated with an 
access point.

●

AP Performance

 - This mode is used to determine the performance of a specific access point within 

the drawing. 

Summit WMScanner requires a working WLAN card for recording measurement data. 

Setup Measurement Run

Select Record New Data
Setup Measurement Run Options

Specify Mode and Record

Measurements

Select Marker Mode or Track Mode
Perform Measurements
Save Results

Visualize Measurement Results

Select Visualization Display
Options
View Results (Channel, Coverage,
Interference, SSID, Throughput)

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов