Extreme Networks Summit WMScanner Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 61

Summit WMScanner Users Guide

59

Preferences Dialog

Summit WMScanner

offers many different configuration preferences for your convenience. These

preferences allow you to configure the file paths, printers, autosave, pointer devices, fonts, colors, and
many other settings. This section describes each of the tabs in the

Preferences

dialog.

Preferences - Files

The

Files

tab in the

Preferences

dialog box presents the options noted on the next page. Most of the

settings are determined during installation, or are derived from your computer’s Windows profile
(under Windows XP/Vista 32/Vista 64), and do not need to be changed under normal circumstances.
Note the

Automatic Save File Location

folder. This specifies where the Auto-Save feature saves the

drawing file.

«
...
59
60
61
62
63
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов