Extreme Networks Summit WMScanner Скачать руководство пользователя страница 59

Страница: 59 / 217

Summit WMScanner Users Guide

Click the

Pick Point

button and then click on the drawing to re-record the x, y points. Enter the WGS84

latitude and longitude for these newly recorded points. Click the

button to exit the dialog box by

recording the edited values; click the

Cancel

button to exit the dialog box without recording the new

values and ignore the new changes.

Utilities - Drawing Legend

Selecting

Utilities > Legend

opens the

Drawing Legend

dialog.

●

The information you enter in the

Drawing Legend

dialog box is for your reference and may be filled

out with any text that you wish. The check boxes in the lower left corner of the

Drawing Legend

dialog box allow you to set what information the legend may display automatically. Once you have
configured the legend, use the

Set Position

button to configure where the legend will be displayed on

the drawing. When you press the

Set

Position

button, you will then be prompted to click in the

Содержание Summit WMScanner


























































































































































































































Результаты поиска

Содержание Summit WMScanner

Отзывы:

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 59 / 217

Результаты поиска

Содержание Summit WMScanner

Отзывы: