manualshive.com logo in svg

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 215 / 217

Поделиться
Скачать
Extreme Networks Summit WMScanner Скачать руководство пользователя страница 215

Summit WMScanner Users Guide

213

A

Customer Support

NOTE

Services can be purchased from Extreme Networks or through one of its channel partners. If you are an end-user 
who has purchased service through an Extreme Networks channel partner, please contact your partner first for 
support.

Extreme Networks Technical Assistance Centers (TAC) provide 24x7x365 worldwide coverage. These centers are 
the focal point of contact for post-sales technical and network-related questions or issues. TAC will create a 
Service Request (SR) number and manage all aspects of the SR until it is resolved. For a complete guide to 
customer support, see the Technical Assistance Center User Guide at:

www.extremenetworks.com/go/TACUserGuide

The Extreme Networks eSupport website provides the latest information on Extreme Networks 
products, including the latest Release Notes, troubleshooting, downloadable updates or patches as 
appropriate, and other useful information and resources. Directions for contacting the Extreme 
Networks Technical Assistance Centers are also available from the eSupport website at:

https://esupport.extremenetworks.com

Registration

If you have not already registered this product with Extreme Networks, you can register on the Extreme 
Networks website at:

http://www.extremenetworks.com/go/productregistration

Documentation

Check for the latest versions of documentation on the Extreme Networks documentation website at:

http://www.extremenetworks.com/go/documentation

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов