Extreme Networks Summit WMScanner Скачать руководство пользователя страница 188

Страница: 188 / 217

Model Building

Summit WMScanner Users Guide

186

Zones are of the following three types:

●

Reader:

The logical reader zones are polygons that contain the “read” zones of one or more RFID

readers. The RFID tag is mapped to a zone based on the coordinates of the antenna that actually
read the tag.

●

Locationing:

Locationing zones indicate that position locationing services are available within these

zones.

●

GeoFencing:

GeoFence zones indicate that GeoFencing services are available within these zones.

You can define a zone in the drawing by selecting

Format Building > Zone > Add/Edit/Remove Zone.

Selecting the

Add/Edit/Remove Zone

command displays the following dialog box:

Содержание Summit WMScanner


























































































































































































































Результаты поиска

Содержание Summit WMScanner

Отзывы:

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 188 / 217

Результаты поиска

Содержание Summit WMScanner

Отзывы: