manualshive.com logo in svg

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 170 / 217

Поделиться
Скачать
Extreme Networks Summit WMScanner Скачать руководство пользователя страница 170

Model Building

Summit WMScanner Users Guide

168

You will be asked to perform two tasks when you press the 

Assemble Floors

 button:

 (1) Set the legend 

position and (2) Verify the drawing

. These two steps are described in detail in the sections that follow.

Drawing Legend.  

When you assemble the building floors, the 

Drawing Legend

 dialog box appears. 

●

The information you enter in the 

Drawing Legend 

dialog box are for your reference and may be 

filled out with any text that you wish. The check boxes in the lower left corner of the

 Drawing 

Legend

 dialog box allows you to set what information the legend displays in the drawing 

window. Once you have configured the legend, use the 

Set Position 

button to configure where the 

legend will be displayed in the drawing window. When you press the 

Set Position

 button, you 

will then be prompted to click in the drawing to set the new legend position. Choose the point in 
the drawing where you want the lower left corner of the legend to appear.

●

Once you have finished configuring and placing the legend, press the 

OK

 button to dismiss the 

Drawing Legend

 dialog box and continue to the Verify Drawing step. You may edit the drawing 

legend at a later time by accessing the menu command 

Utilities > Legend.

Verifying Drawing Assembly.  

Once you chosen to assemble building floors and then configured the drawing legend, you will be asked 
to verify that the drawing appears as you intended it to. This is your opportunity to make sure that you 
properly set the alignment points for a multi-floor building by making sure the floors stack up properly. 
The 

Verify Drawing 

dialog box allows you to view the assembled drawing from multiple perspectives 

and to make sure floors are scaled relative to each other.

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов