Extreme Networks Summit WMScanner Скачать руководство пользователя страница 160

Страница: 160 / 217

Measurement Surveys

Summit WMScanner Users Guide

158

●

Remove:

To remove an antenna, select the antenna and then click the remove button. To remove

multiple antennas, press the CTRL key and select multiple antennas and then click the Remove
button.

●

Move:

To move an antenna, select the antenna and then click at the location in the drawing where

you want the antenna to be placed.

Once you have finished the editing of the antenna, you can click the Done button to go back to the
Edit RFID dialog box.

Reference Tags

Summit WMScanner allows you to place fixed reference tags as part of its integration with WMS. By
placing fixed reference tags within a network design, the WMS

Real Time Locationing System

(RTLS) can

associate the position of these tags to wireless equipment within the facility and it can thus improve the
accuracy of its position determination.

Placing Reference Tags

You can place a reference-tag at a desired location in the drawing by selecting

Equipment > Reference-Tag

> Place Reference-Tag.

Содержание Summit WMScanner


























































































































































































































Результаты поиска

Содержание Summit WMScanner

Отзывы:

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 160 / 217

Результаты поиска

Содержание Summit WMScanner

Отзывы: