Extreme Networks Summit WMScanner Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 159

Summit WMScanner Users Guide

157

Adding/Editing the Antenna

Clicking on the

Antenna

button on the

Edit RFID

dialog box displays the

Antenna Association

dialog box.

This allows you to add a new antenna, and edit, remove, move the existing antennas. This dialog box
displays the RFID information such as the model of RFID reader and the maximum number of antennas
that can be associated with the RFID reader.

●

Add:

to add an antenna to the RFID reader click the Add button and then Click at the location in the

drawing, where you would like the antenna to be placed. You can also choose to place an antenna
away from the RFID reader. Continue to Click on the drawing until you are done with the antenna
placement. If you reach the maximum limit, the Summit WMScanner displays a warning message.

NOTE

To enable the add button select any empty field in any of the columns available.

●

Edit:

this option allows you to edit the x-coordinate, y-coordinate, and antenna height. This enables

you to enter the absolute position of the antenna on the floor within the building. All coordinates are
given relative to the origin (also called the Floor Alignment Point) of the building coordinate system.
Summit WMScanner does not allow you to change the floor of the antenna, as the antenna can only
be placed on the same floor as that of the RFID reader.

«
...
157
158
159
160
161
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов